manualshive.com logo in svg

Central Machinery 67595, Set Up And Operating Instructions Manual, Page: 11 / 34

Share
Download
Central Machinery 67595 Set Up And Operating Instructions Manual Download Page 11

Page 11

For technical questions, please call 1-800-444-3353.

SKU 67595 

        

9a

10a

Figure For Step 1-7

7.  Attach the Motor Plate (10A) to the Motor 

Plate Bracket (9A).  Connect the end that 

is folded back on itself.

Figure For Step 1-8

10a

7a

8.  Attach the other end of the Motor Plate 

(10A) to the Horizontal Brace (7A).
Make sure the stand rests square on the 

9. 

floor and that the Mounting Plate (1A) 

is level.  Then, 

wrench tighten

 all Nuts 

from phase 1 securely.

phaSe 2: Bandsaw Body to Stand 

assembly

h

j

k

B

required hardware

letter

description

qty

(for this phase)

B

M8 x 40 Bolt

4

H

M8 Washer

8

J

M8 Lock Washer

4

K

M8 Nut

4

Belt 

cutout

Stand 

Mounting 

SlotS

part 1a

Figure For Step 2-1

top View

1.  Orient the Saw Body with the Stand be-

fore lifting it.  The Pulley(s) need to align 

over the belt cutout and the four bolt 

holes must line up with the stand mount-

ing slots, as shown above.

Summary of Contents for 67595



































Reviews:

No comments