background image

Page 4

For technical questions, please call 1-800-444-3353.

Item 61373 

        

SAFET

y

Op
ERA
TION

M

AINTENAN

c

E

SETU
p

17. Maintain labels and nameplates on the tool.  

These carry important safety information.  

If unreadable or missing, contact 

Harbor Freight Tools for a replacement.

18. Avoid unintentional starting.   

Prepare to begin work before turning on the tool.

19. This product is not a toy.  Keep it 

out of reach of children.

20. People with pacemakers should consult their 

physician(s) before use.  Electromagnetic fields in 

close proximity to heart pacemaker could cause 

pacemaker interference or pacemaker failure.

21. WARNING: Some dust created by power 

sanding, sawing, grinding, drilling, and other 

construction activities, contains chemicals 

known [to the State of California] to cause 

cancer, birth defects or other reproductive harm.  

Some examples of these chemicals are: 

• Lead from lead-based paints 

• Crystalline silica from bricks and cement or other 

masonry products 

• Arsenic and chromium from 

chemically treated lumber

Your risk from these exposures varies, 

depending on how often you do this type of work.  

To reduce your exposure to these chemicals: 

work in a well ventilated area, and 

work with approved safety equipment, such 

as those dust masks that are specially 

designed to filter out microscopic particles.  

(California Health & Safety Code § 25249.5, 

et seq.

)

22. WARNING: Handling the cord on this product will 

expose you to lead, a chemical known to the State of 

California to cause cancer, and birth defects or other 

reproductive harm.  Wash hands after handling.  

(California Health & Safety Code § 25249.5, 

et seq.

)

23. The warnings, precautions, and instructions 

discussed in this instruction manual cannot cover all 

possible conditions and situations that may occur.   

It must be understood by the operator that 

common sense and caution are factors 

which cannot be built into this product, 

but must be supplied by the operator.

 SAVE THESE INSTRUcTIONS.

Grounding Instructions

 

TO pREVENT ELEcTRIc SHOcK AND DEATH FROM INcORREcT 

GROUNDING WIRE cONNEcTION READ AND FOLLOW THESE INSTRUcTIONS:

110-120 V~ Grounded Tools: Tools with Three prong plugs

1.  In the event of a malfunction or breakdown, 

grounding provides a path of least resistance for 

electric current to reduce the risk of electric shock. 

This tool is equipped with an electric cord having an 

equipment-grounding conductor and a grounding 

plug.  The plug must be plugged into a matching 

outlet that is properly installed and grounded in 

accordance with all local codes and ordinances.

2.  Do not modify the plug provided – if it will 

not fit the outlet, have the proper outlet 

installed by a qualified electrician.

3.  Improper connection of the equipment-grounding 

conductor can result in a risk of electric shock. 

The conductor with insulation having an outer 

surface that is green with or without yellow 

stripes is the equipment-grounding conductor. 

If repair or replacement of the electric cord or 

plug is necessary, do not connect the equipment-

grounding conductor to a live terminal.

Log Splitter Safety Warnings (continued)

Summary of Contents for 61373

















Reviews: