9
ENGLISH
B1300
NR 14AF035
RESET
SW:S1J41AH
LED
OFF
F
m
= 125.2 kN
Fp = 94.5 kN
F
m
= 14.07 ton
Fp = 10.61 ton
1000
-12000
BATTERY
3 SEC.
ERROR
001
13001
BATTERY
F
m
= 125.2 kN
F
p
= 102.3 kN
P
m
= 692 bar
P
p
= 565 bar
F
m
= 125.2 kN
OK
P
m
= 692 bar
OK
P
m
= 10037 psi
Pp = 7575 psi
002
003
BATTERY
004
LED
ON
LED
OFF
3 SEC.
LED
ON
max.
BATTERY
BATTERY
min.
P
m
= 692 bar
Pp = 522.3 bar
Do not apply pressure to or stab at the touch button, a light touch using a bare
finger is sufficient. The command pulse is sent when the finger releases the button.
2.8) Battery status
The battery is equipped with LED indicators that indicate the
remaining battery life at any time by pressing the adjacent
button (P):
4 LEDs illuminated: fully charged
2 LEDs illuminated: 50 % capacity
1 LED flashing: minimum charge, replace the battery.
With the battery inserted into the tool, the remai-
ning battery life can also be checked on the display,
via touch button selection (Ref. to § 7).
The screen shown alongside indicates that the battery voltage has
dropped below a minimum safety threshold; under these conditions
the tool will not start, and it is necessary to recharge or replace the battery.
The approximate time to fully recharge a battery is about 80 minutes.
After each working cycle, and after the extraction of the battery from the tool, an integrated
battery cut-off device will operate after 70 s approx.
Then the LED nearest to button (P) will flash 5 times each 14 s approx. The battery will be reactivated
when it is reintroduced into the tool and the operating button is pressed.
2.9) Using the battery charger
Carefully follow the instructions in the battery charger user manual.
3. MAINTENANCE
The tool is robust, completely sealed, and requires very little daily maintenance. Compliance with
the following points, should help to maintain its optimum performance:
3.1) Thorough cleaning
Dust, sand and dirt are a danger for any hydraulic device.
Every day, after use, the tool must be wiped with a clean cloth taking care to remove any residue,
especially close to pivots and moveable parts.
Do not use Hydrocarbons to clean the rubber parts.
3.2) Storage case
When not in use, the tool should be stored and transported in the plastic case, to prevent damage.
The case, type VAL P41, is suitable for storing the tool, the accessories and up to 12 die sets and
pre-prepared compression connectors.
VAL P41: Size 691x456x176 mm (27.2x17.9x6.9 inches). Weight 4 kg (8.8 lbs).
B1300
NR 14AF035
RESET
SW:S1J41AH
LED
OFF
F
m
= 125.2 kN
Fp = 94.5 kN
F
m
= 14.07 ton
Fp = 10.61 ton
1000
-12000
BATTERY
3 SEC.
ERROR
001
13001
BATTERY
F
m
= 125.2 kN
F
p
= 102.3 kN
P
m
= 692 bar
P
p
= 565 bar
F
m
= 125.2 kN
OK
P
m
= 692 bar
OK
P
m
= 10037 psi
Pp = 7575 psi
002
003
BATTERY
004
LED
ON
LED
OFF
3 SEC.
LED
ON
max.
BATTERY
BATTERY
min.
P
m
= 692 bar
Pp = 522.3 bar
B1300
NR 14AF035
RESET
SW:S1J41AH
LED
OFF
F
m
= 125.2 kN
Fp = 94.5 kN
F
m
= 14.07 ton
Fp = 10.61 ton
1000
-12000
BATTERY
3 SEC.
ERROR
001
13001
BATTERY
F
m
= 125.2 kN
F
p
= 102.3 kN
P
m
= 692 bar
P
p
= 565 bar
F
m
= 125.2 kN
OK
P
m
= 692 bar
OK
P
m
= 10037 psi
Pp = 7575 psi
002
003
BATTERY
004
LED
ON
LED
OFF
3 SEC.
LED
ON
max.
BATTERY
BATTERY
min.
P
m
= 692 bar
Pp = 522.3 bar
P
Summary of Contents for B1300-C-KV
Page 47: ...47...
