21
12.2 Device settings
You can change the device settings from the Device Manager utility
(available for PC and MAC on
www.interphone.com
) or from the Interphone
UNITE app.
Attention: the setting "Advanced Features" will enable the following
headeset features:
• The private MESH mode called “GROUP MESH”
• Reset Mesh
• Phone multiple speed dial
• Conference in phonecall
• Smart FM station seek
12.2.1 Speed dial
Assign phone numbers for speed dialing to make a phone call quickly.
12.2.2 Channel Setting (Default: channel 1)
If the Open Mesh communication experiences interference because other
groups are also using the channel 1 (default), change the channel. You can
select one of 1 to 9 channels.
12.2.3 Unit Language
You can select the device language. The selected language is maintained
even when the headset is rebooted
12.2.4 Audio Equalizer (Default: Off)
You can use the Audio Equalizer to increase/decrease the decibel level of
different frequency ranges of audio.
• Balance will adjust all of the frequency ranges to be the same volume
level (0 dB).
• Bass Boost will increase the bass range of audio (20 Hz - 250 Hz).
• Mid Boost will increase the mid range of audio (250 Hz - 4 kHz).
• Treble Boost will increase the high range of audio (4 kHz - 20 kHz).
12.2.5 VOX Phone (Default: Enable)
If this feature is enabled, you can answer incoming calls by voice. When
you hear a ringtone for an incoming call, you can answer the phone by
saying a word such as “Hello” loudly or by blowing air into the microphone.
VOX phone is temporarily disabled if you are connected to intercom. If this
feature is disabled, you have to tap the Center Button to answer an incoming
call.
12.2.6 VOX Intercom (Default: Disable)
If VOX Intercom is enabled, you can initiate an intercom conversation with
the last connected intercom by voice. When you want to start intercom, say
a word such as “Hello” loudly or blow air into the microphone. If you start an
intercom conversation by voice, the intercom terminates automatically when
you and your intercom friend remain silent for 20 seconds. However, if you
manually start an intercom conversation by tapping the Center Button, you
have to terminate the intercom conversation manually. However, if you start
the intercom by voice and end it manually by tapping the Center Button, you
will not be able to start intercom by voice temporarily. In this case, you have
to tap the Center Button to restart the intercom. This is to prevent repeated
unintentional intercom connections by strong wind noise. After rebooting
the headset, you can start the intercom by voice again.
12.2.7 VOX Sensitivity (Default: 3)
VOX sensitivity can be adjusted depending on your riding environment.
Level 5 is the highest sensitivity setting and level 1 is the lowest.
12.2.8 Bluetooth
®
Intercom Audio Multitasking (Default:
Disabled)
Audio Multitasking ( Bluetooth
®
Intercom Audio Multitasking and Mesh
Intercom Audio Multitasking) allows you to have an intercom conversation
while simultaneously listening to music, FM radio, or GPS instructions. The
overlaid audio is played in the background with reduced volume whenever
there is an intercom conversation and will return to normal volume once the
conversation is finished.
The Mesh Intercom Audio Multitasking feature is always on.
Note:
• For Bluetooth
®
Intercom Audio Multitasking to work properly, you need to
power the headset off and on. Please restart the headset.
• Bluetooth
®
Intercom Audio Multitasking will be activated during two-way
intercom conversations with a headset that also supports this feature.
• Some GPS devices may not support this feature.
• The Audio Multitasking feature can be configured through the Intercom-
Audio Overlay Sensitivity and the Audio Overlay Volume Management
settings.
Summary of Contents for Interphone U-COM 16
Page 1: ...User manual...
