manualshive.com logo in svg

CELLmatic 1502 GSF, User Manual

Share
Download
CELLmatic 1502 GSF User Manual Download Page 44

CELLmatic 1502 – GSV/GSF 

Issue: 2.1 

User Manual 

08.02.2004 

 

Page 43 of 51 

 

Thy

-

tronic

 I/S – Bjørnevej 8c – DK 7700  Thisted – Tel.: +45 97982344 – Email.: [email protected]

 

I/O PICTURES 

 

DIGITAL OUTPUTS 12-23, CONTACTORS 

 

 
                        01-01-94  17:25:35 
   SETUP 1/I/O/J1-J7-J8 OUT 12-23/          
F6 OUT 16-23:Digital output 16-23           
F5 OUT 15   :Common alarm     OFF           
F4 OUT 14   :Oil heater       OFF           
F3 OUT 13   :Oil pump start   OFF           
F2 OUT 12   :Compressor start OFF           
F1 STOP     :                         STOP  
 

 

OUT 16-23  DIGITAL OUTPUTS  16-23 
 

  Function key F6 can be used to leaf to the I/O picture showing digital inputs "OUT 16" to "OUT 23" 

 

OUT 15 OIL HEATER 
"ON" means that the heater in the oil separator is switched on. 

 

OUT 14 COMMAN ALARM 
 

If an alarm has appeared on the unit the output will go "ON". The signal can for instance be used for a 
remote message that there is an alarm at the compressor unit. 

 

OUT 13 PUMP START 
 

When this output goes "ON" the oil pump is started. The pump is stopped again when the output goes 
"OFF". 

 

OUT 12 COMPR. START 
 

When this output goes "ON" the compressor is started. It is stopped again when the output goes 
"OFF". 

 

 
 
   03-06-96 

 

13:48:15 

   /I/O/J1-J7-J8/OUT 12-23/OUT 16-23        
F6 OUT 20-23:Digital output  20-23          
F5 OUT 19   :Start Slave      OFF           
F4 OUT 18   :Booster start    OFF           
F3 OUT 17   :Common cutout    OFF           
F2 OUT 16   :Max. Output      OFF           
F1 STOP     :                               
   

 

 

OUT 20-23  DIGITAL OUTPUTS  20-23 
 

  Function key F6 can be used to leaf to the I/O picture showing digital inputs "OUT 20" to "OUT 23"

 

 

OUT 19 SLAVE START 
 

  If this compressor panel is to control a subsequent slave compressor, the start signal is sent via this 

output which then goes ON. 

 

OUT 18 BOOSTER START 
 

 

If the compressor panel is to control a booster compressor (low-pressure compressor) the 

start signal to the booster compressor is applied at this output. When the signal goes "OFF" the 
booster is stopped. 

 

 

 

 

OUT 17 COMMON CUTOUT 
 

"ON" means that there is a cutout at the unit. This signal can for instance be used for calling the 
operator. 

 

OUT 16 MAX. OUTPUT 
 

  If a digital signal is required to show that the compressor is running at maximum capacity, this output 

can be used. The output goes ON when yield is >97%. 

Summary of Contents for 1502 GSF




















































Reviews:

No comments

Brands by name

Popular brands

Load more brands