5.3.6.2. BACKUP & RESTORE CONFIGURATION
Section
Backup/Restore
enables backup or restore the user configuration to/from a file on PC or server.
5.3.6.3. FIRMWARE UPDATE
Section
Update Firmware
enables to make the update firmware form the file. Firstly should be done update the POST before
updating the firmware – more details available after contact with the Service by e-mail: [email protected]
5.3.6.4. FACTORY DEFAULT SETTINGS
The converter was configured by the manufacturer.
Restoring the factory default settings will clear all current settings and automatically reboot the converter.
5.3.6.5. SYSTEM INFORMATION
Section
System Information
has section:
-
General
– device model , MAC address, firmware version, Boot version, POST version and more.
-
GPIO
– not applicable ADA-13040MG .
-
Serial
– port description, current settings of serial port, status of controlling lines and the statistics data transfer through the serial
port.
-
Network
– show statistics of ETHERNET interface for IP, TCP, UDP, ICM protocols.
5.3.6.6. REBOOT
Section
Reboot
allows to make software reset of ADA-13040MG. Pressing [
Reboot
] will start rebooting of server during 1 min.
5.3.6.7. LOGOUT – ENDING THE MANAGEMENT
If all the configuration were done, press
Logout
on left panel.
6. USING VIRTUAL PORT SERVICE [REALPORT]
6.1. VIRTUAL PORT DRIVER INSTALLATION IN WINDOWS XP
The installation of virtual serial port drivers should be done for the CD, by choosing:
- Drivers/Win98SEME – for Windows 98, Windows 98SE, Windows ME Operating systems,
- Drivers/Win2000 – for Windows2000 Operating systems,
- Drivers/WinXP2003Vista_x86_x64 – for Windows XP, Windows Server2003, Windows Vista Operating systems.
Installation of Virtual serial port drivers is as follow:
1. Connect ADA-13040MG to ETHERNET (see p.3.2.1) and power (see p.3.2.6),
2. Press [
Start
] and select [
Run...
]
3.
in the dialog window [
Run
] press [
Browse
]
4. select „
My computer
” and CD-Rom with „
ADANET_DRV
”.
5. select catalog
Drivers/WinXP2003Vista_x86_x64
.
6. select file „
Setup32.exe
” for 32-bits system or „
Setup64.exe
” for 64-bits and press [
Open
].
7. when the installation window will appear press [
Next
] .
8. the searching will start for converters in the network, found devices will be added to the list.
9. select the converter from the list for installation of virtual port driver and press [
Next
].
10. in window Describe the device select or not the Starting Com port and press [
Finish
]. The driver will be installed.
The Virtual serial port drivers can be installed without connection of ADA-13040MG to ETHERNET ETHERNET and it is as
follow:
1.
press [
Start
] button, select [
Run...
]
2. in the dialog window [
Run
] press [
Browse
]
3. select „
My computer
” and CD-Rom with „
ADANET_DRV
”.
4. select catalog
Drivers/WinXP2003Vista_x86_x64
.
5. select file „
Setup32.exe
” for 32-bits system or „
Setup64.exe
” for 64-bits and press [
Open
].
6. when the installation window will appear press [
Next
] .
7. the searching for converters in the network will start.
8. if no devices were not found press [
Next
].
9. in the window Describe the device should be set:
– IP address for converter,
– number of installing COM port (No. Ports)
– Starting COM
and press [
Finish
]. The driver will be installed.
In this way installed virtual port can require the configuration in case of connecting the converter to network.
24
ADA-13040MG
