CEECO SSW-323-F Service Manual Download Page 18

ISSUE 4.0 

CEECO 

Communication Equipment & Engineering Company 

PROPRIETARY 

18

12.0    WARRANTY POLICY 

 
 

12.1

   GENERAL 

 

CEECO guarantees its products to be free from defects in material and 
workmanship for a period of 365 days from the date of original purchase.  
CEECO's obligation under this warranty is limited to repair or 
Replacement of any part found to be defective by CEECO. 

 

UNDER NO CIRCUMSTANCES shall CEECO be liable for loss, 
damage, cost of repair or consequential damages of any kind, which have 
been caused by neglect, abuse or improper operation of equipment. 

 

CEECO will repair or replace any unit during this period if found to be 
defective for reasons other than abuse and improper use or improper 
installation.  It is the buyer’s responsibility to return the defective unit to 
the factory. CEECO will then repair or replace any defective parts and 
return them to the buyer free of charge. 

 
 

12.2

   PRINTED CIRCUIT BOARDS 

 

Printed circuit boards should not be repaired in the field. If a unit is found 
to be faulty, replace it with another unit and return the faulty unit to 
CEECO for repair.  Modifications by any one other than CEECO will void 
the warranty. 
 

Summary of Contents for SSW-323-F




















Reviews: