10
• Connect connector
B
, introduce the welding torch
body into the grip seat and then connect connector
A
by
introducing it inside the grip as shown in igure 4.
• Reposition
LH
grip making sure not to latten any wire
between the grip rims.
• Screw in the 6 screws V again.
5.3.2 Replacing the welding torch body CP162C MAR
• Unscrew the cable gland
F
Fig.7;
• Unscrew the retention dowels
G1
and
G2,
then handle
M
, pull it back until all cables are shown (see Fig. 8).
• Disconnect connector
A
and connector
B
(pilot arc).
• Remove heat shrinking hose
C
and unscrew nut
D
(wrench #13) by keeping itting
E
(wrench #11) fastened.
• Replacing the welding torch body.
• Screw in ittings
D
and
E
according to the arrow
direction - Fig .8
• Tighten ittings, introduce the heat-shrinking hose
C
and use a small heat source to warm it up. Make sure
that ittings are completely covered.
• Reconnect connectors
A
and
B
, screw in the handle
M
and then, the retention dowels
G1
and
G2
.
• Screw again cable gland
F
.
5.4 REPLACING THE GRIP WITH PUSH-BUTTON CP-
162C MAR
• Unscrew the 6 screws
V
Fig.3 and remove the
LH
grip.
• With reference to Fig.4, lift the welding torch body with
cable and disconnect connector
A
(push-button) .
• Replace the grip with push-button, connect connector
A
and introduce it inside the grip, as shown in igure 4,
and then position the welding torch body with cable
inside the
RH
grip seat.
• Fasten the LH side of the grip making sure not to latten
any wire between the grip rims and then screw the 6
screws
V
again.
5.5
REPLACING THE CABLE WITH CENTRAL
ADAPTER.
5.5.1 CP162C MAR
Fig. 6
T
A
B
• Unscrew the 6 screws
V
Fig.3 and remove the
LH
grip. With reference to
Fig.4, lift the welding
torch body with cable
and
disconnect
connector
A
(push-
button) and connector
B
(pilot arc).
•
Remove
heat
shrinking hose
C
and
unscrew nut
D
(wrench
#13) by keeping itting
E
(wrench #11) fastened.
•
Replace
the
welding torch cable,
manually screw ittings
D
and
E
according to the
arrow direction - Fig.6.
• Tighten ittings, introduce the heat-shrinking hose
C
and use a small heat source to warm it up.
• Connect connector
B
, introduce the welding torch
body into the grip seat and then connect connector
A
by introducing it inside the grip as shown in igure 4.
• Reposition
LH
grip making sure not to latten any wire
between the grip rims.
• Screw in the 6 screws
V
again.
5.5.2 CP162C DAR
• Remove cable gland
F
Fig.7.
• Unscrew the retention dowels
G1
and
G2,
then handle
M
and pull it back until all cables are shown (see Fig. 8);
• Disconnect connector
A
and connector
B
(pilot arc).
• Remove heat shrinking hose
C
and unscrew nut
D
(wrench #13) by keeping itting
E
(wrench #11) fastened.
• Replacing the welding torch cable.
• Screw in fittings
D
and
E
according to the arrow direction - Fig.8.
• Tighten ittings, introduce the heat-shrinking hose
C
and use a small heat source to warm it up. Make sure
that ittings are completely covered.
Fig. 5
Fig. 4
C
B
B
E
D
A
T
Fig. 3
V
V
V
V
V
V
