background image

7

cdvigroup.com

EN

AIOM

10-Input/10-Output Module

  INSTALLATION MANUAL

EN

AIOM

10-Input/10-Output Module

  INSTALLATION MANUAL

Location and Mounting

The cabinet is designed to be installed indoors, in a safe and secure location. Suggested locations include 

electrical rooms, communication equipment rooms, closets or in the ceiling. To save time, wiring and facilitate 

testing, install the cabinets at an equal distance between its controlled doors. Normal temperature and humidity 

levels should be maintained.

Cabinet Dimensions:

 

29 cm (11.4”) high, 28 cm (11”) wide, 8 cm (3.15”) deep

Multiple Conduit Knock-outs:

 

Two 19.05mm (0.75”) on each side and one 12.7mm (0.5”) on top

Minimum Clearance For Cabinet:

 

25cm (10”) clear space around all sides

 

38cm (15”) clear space in front of cabinet

Minimum Clearance From Electrical Interference:

 

2.4m (8ft.) from high voltage equipment or wiring and from electrical equipment likely to generate 

interference

 

1.2m (4ft.) from telephone equipment or lines and 8m (25ft.) from transmitting equipment

 

The system’s location and wiring methods shall be in accordance with the National Electrical Code, 

ANSI/NFPA 70.

Summary of Contents for AIOM

























Reviews: