CD Automation CD3200 User Manual Download

Page: 9 / 50

CD Automation srl

CD3200-1PH from 15A to 110A

User’s Manual

2.4

Software Configurator

The software configuration is free and is possible

download it from our site:

www.cdautomation.com

If the Order Code is in line with requirement, then

CD3200 has been already configured in Factory

and it's ready to use.

You need the software only to modify the ordered

configuration. Anyway we suggest to check the

unit on the machine with the "Test unit" section.

For install the software, launch the program and

follow the instructions on the screen.

To connect the unit at the PC, it's necessary use

the programming cable connected between the PG

connector (see par. 11.6) and the serial port

RS232 of the PC.

The programming cable is not included.

With the CD-RS serial converter is possible

configure the Thyristor unit also through the

RS485 (see par. 11.7).

For this solution, the programming cable is not

necessary.

Run the software configurator and set the serial

port of the PC with con baudrate =9600 and the

address of Thyristor unit (default=1).

Summary of Contents for CD3200



















































Search results

Summary of Contents for CD3200

Reviews:

Related manuals for CD3200

Brands by name

Popular brands

CD Automation CD3200, User Manual

Search results

Summary of Contents for CD3200

Reviews:

Related manuals for CD3200

Brands by name

Popular brands