background image

Technicalinst. guide

Limpido XC2

v4.0

Screen

Function

Option: No

CAUTION: This screen is used to configure the menus for
your device depending on its equipment and version. Do not
change this setting, leave it as No

Reset to zero

Confirm reset?

This screen is used to reset all the control box settings. A .

This  resets  all  the  settings  to  their  default
factory  value.  Your  device  will  need  to  be
reconfigured.

Config enable

This  screen  is  used  to  prevent  the  user  from  accessing  the
different device configurations. (See Appendix A)

6.6.4. Exiting the supervisor menu

Supervisor mode can be exited by turning the device off and then back on again after about thirty
seconds, using the ON/OFF button.

6.6.5. Reset to zero

It may be necessary to reset the Limpido XC2.

This returns all the settings to their default factory value. Your device will need
to be reconfigured .

To do this:

1.

Power off the electrolysis unit using the ON/OFF button on the control box,

2.

Wait for about 30 seconds,

3.

Press the 

 and 

 keys and keep them pressed,

4.

Power the electrolysis unit back on using the ON/OFF button on the control box and release
the keys,

5.

Resetting the device requires its full reconfiguration. Select the model corresponding to your
version of cell and validate using the 

 key.

LIMPIDO XC2 60/100/160

www.c-

cei.fr

22

Summary of Contents for Limpido XC2



























Reviews: