Cattron-Theimeg LRC-L1 User Manual Download Page 19

Page: 19 / 26

User Manual LRC-L1

Version 1.0.0 - 11/2010

Subject to change without notice.

7 Technical Data

7.1 Technical Data Transmitter

7.2 Technical Data Battery Charger

Transmitter series

LRC-L1

Frequency bands

335 MHz
418 MHz
433 MHz
447 MHz
869 MHz
915 MHz

Transmission speed

4.8 - 20 kbps

Transmitter output power

< 5 mW / < 10 mW
depending on frequency band

Antenna

internal

System addresses

24 bit

Power-saving mode

automatic switch-off
(configurable 0 – 30 minutes)

Power supply

Autonomy

NiMH, 4.8 V / 1600 mAh,
Quick-swap rechargeable battery
>12 h @ 100% duty cycle

Control elements

variable

Indication

1 Status LED for status and error indication
4 Multi-LEDs for RF channel selection
1 Buzzer
LCD Display (optional)

Weight

approximately 1.6 kg

Dimensions (W x H x D)

320 x 255 x 185 mm

Housing

Plastic, standard colours: red/grey

Operating temperature

-20 ºC ... +60 ºC

Protection class

IP 65

STOP command

EN 954-1 Category 3 for all safety relevant functions
EN 13849-1 Performance Level d

Type

Processor-controlled charger

Part number

BT 097-00303

Dimensions (W x D x H) /

60 x 90 x 120 mm

Power supply

Primary: 100-240 VAC, 50/60 Hz, 17 VA, 300 mA
Secondary: 1.45 - 14.5 VDC. 800 mA, 9.6 VA

Summary of Contents for LRC-L1



























Search results

Summary of Contents for LRC-L1

Reviews:

Related manuals for LRC-L1

Brands by name

Popular brands

Cattron-Theimeg LRC-L1, User Manual

Search results

Summary of Contents for LRC-L1

Reviews:

Related manuals for LRC-L1

Brands by name

Popular brands