background image

CHAPTER

1

P/N 016-5032-164 Rev. A

1

CHAPTER 1

IMPORTANT SAFETY 

INFORMATION

Read this manual and the operation and safety instructions included with your implement and/or controller 

carefully before installing the SC1™ HDU system.
• Follow all safety information presented within this manual.
• If you require assistance with any portion of the installation or service of your Raven equipment, contact your 

local Raven dealer for support.

• Follow all safety labels affixed to the SC1 HDU system components. Be sure to keep safety labels in good 

condition and replace any missing or damaged labels. To obtain replacements for missing or damaged safety 

labels, contact your local Raven dealer.

When operating the machine after installing SC1 HDU, observe the following safety measures:
• Be alert and aware of surroundings.
• Do not operate SC1 HDU or any agricultural equipment while under the influence of alcohol or an illegal 

substance.

• Remain in the operator’s position or a safe working distance away from the booms at all times when SC1 HDU 

is engaged.

• Disable SC1 HDU when exiting from the operator’s seat and machine.
• Do not drive the machine with SC1 HDU enabled on any public road.
• Determine and remain a safe working distance from other individuals. The operator is responsible for disabling 

SC1 HDU when the safe working distance has diminished.

• Ensure SC1 HDU is disabled prior to starting any maintenance work on SC1 HDU or the machine.

• When starting the machine for the first time after installing SC1 HDU, be sure that all persons stand clear in 

case a hose has not been properly tightened.

• The machine must remain stationary and switched off, with the booms unfolded and supported, during 

installation or maintenance.

NOTICE

 

WARNING

 

CAUTION

Summary of Contents for Titan 4 Series































Reviews: