Cascade X2000 Use And Care Manual Download Page 2

Page: 2 / 31

IMPORTANT SAFETY INFORMATION

Read this manual carefully before using your grill to reduce the risk of fire, burn

hazard or other injury.

- Extreme care should be used because of the high temperatures produced by this

appliance. CHILDREN SHOULD NOT BE LEFT UNATTENDED IN AN AREA

WHERE THE GRILL IS BEING OPERATED.

- This appliance must be kept clear from combustible materials, gasoline or other flammable vapors and liquids. Do not

allow flammable materials to come in contact with grate, burner or hot surfaces.

- Use only outdoors and provide good ventilation to avoid carbon monoxide build-up which could result in injury or death.

- Do not repair or replace any part of this appliance unless it is specifically recommended in this manual. A qualified

service technician should conduct all other service.

- Follow the installation and servicing instructions provided with this product. Have your grill installed by a qualified

service technician.

- Locate the main gas supply valve so that you know how to shut the gas off to your grill.

- If you smell gas, make sure all gas connections are tight before operation. If you continue to smell gas call a

qualified technician.

- When lighting a burner, always pay close attention to what you are doing and be certain you are pushing the igniter

that lights the burner you intend on using.

- Always keep your face and body as far away as from the grill as possible when lighting to reduce the risk of burn.

- Extinguish all flames and do not smoke while engaging gas and igniting the grill.

- A minimum distance of at least 15" must be maintained from any combustible material on both sides and the back of

the grill. Do not place the grill under any overhead unprotected combustible construction.

RECOGNIZE SAFETY SYMBOLS, WORDS AND LABELS

WARNING indicates a potentially hazardous situation which, if

not avoided, could result in death or serious injury.

NOTE indicates an important piece of information that needs to

be observed to ensure the proper operation of your grill.

INSTALLER: Please retain these instructions with the owner so that they may maintain them for

future reference.

DANGER

If you smell gas:

1. Shut off gas to the appliance

2. Extinguish any open flame

3. Open lid

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or your fire department.

WARNING

1. Do not store or use gasoline or other

flammable liquids or vapors in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

Table of Contents

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

General Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Grill Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-17

Gas Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-19
Pre-Operation Leak Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

ighting The Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Using The Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

Using The Rotisserie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Accessory Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26-27

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

Summary of Contents for X2000
































Search results

Summary of Contents for X2000

Reviews:

Related manuals for X2000

Brands by name

Popular brands

Cascade X2000, Use And Care Manual

Search results

Summary of Contents for X2000

Reviews:

Related manuals for X2000

Brands by name

Popular brands