Carrier ZS Application Manual Download Page 7

Page: 7 / 49

Introduction

ZS Sensor

Applications Guide

Remote Sensor:

Temperature sensor

ZS Sensors communicate with the HVAC system through the Rnet.
A ZS zone sensor's functionality is determined by:

•

The ZS sensor model (Standard, Plus, Pro, Pro-F)

•

The sensor's sensing capabilities (temperature, humidity, CO

, VOC, or motion)

•

The control program that runs the associated equipment

REQUIREMENTS

•

All ZS Sensors except the ZS Pro with motion sensor require:

•

The i-Vu® v6.0 or later application

•

v6.0 driver (drv_xxxxxx_6-00-082 or later). Check

Carrier Control Systems Support Site

http://www.hvacpartners.com/

https://accounts.ivusystems.com/

for the latest driver.

•

The ZS Pro with motion sensor requires:

•

The i-Vu® v6.5 or later application

•

v6-00a or later controller driver

•

A BSVI microblock in the control program (even if it is not used)

This document

This document describes how to create control programs for ZS sensors in the Snap application. To use this guide,

you need a working knowledge of control programs and the Snap application.
See the

ZS Sensors Installation Guide

to mount, wire, and communicate with the sensors.

See the

ZS Sensor User Guide

to use the sensors.

Summary of Contents for ZS














































Search results

Summary of Contents for ZS

Reviews:

Brands by name

Popular brands

Carrier ZS, Application Manual

Search results

Summary of Contents for ZS

Reviews:

Brands by name

Popular brands