![background image](http://html.mh-extra.com/html/carrier/weathermaker-50tc07-series/weathermaker-50tc07-series_installation-instructions-manual_2560324020.webp)
20
Step 5 — Field Fabricate Ductwork
Cabinet return-air static pressure (a negative condition) shall
not exceed 0.35 in. wg (87 Pa) with economizer or 0.45 in. wg
(112 Pa) without economizer.
For vertical ducted applications, secure all ducts to roof curb
and building structure.
Do not connect ductwork to unit.
Fabricate supply ductwork so that the cross sectional dimen-
sions are equal to or greater than the unit supply duct opening
dimensions for the first 18-in. (458 mm) of duct length from
the unit basepan.
Insulate and weatherproof all external ductwork, joints, and
roof openings with counter flashing and mastic in accordance
with applicable codes.
Ducts passing through unconditioned spaces must be insulated
and covered with a vapor barrier.
If a plenum return is used on a vertical unit, the return should
be ducted through the roof deck to comply with applicable fire
codes.
FOR UNITS WITH ACCESSORY ELECTRIC HEATERS
All installations require a minimum clearance to combustible
surfaces of 1-in. (25 mm) from duct for first 12-in. (305 mm)
away from unit.
Outlet grilles must not lie directly below unit discharge.
NOTE: A 90 degree elbow must be provided in the ductwork to
comply with UL (Underwriters Laboratories) code for use with
electric heat.
Step 6 — Rig and Place Unit
Keep unit upright and do not drop. Spreader bars are required
for 08-14 size units; size 16 units do not require spreader bars.
Rollers may be used to move unit across a roof. Level by using
unit frame as a reference. See Table 2 and Fig. 15 for additional
information.
Lifting holes are provided in base rails as shown in Fig. 15. Re-
fer to rigging instructions on unit.
Fig. 15 — Rigging Details
CAUTION
PROPERTY DAMAGE HAZARD
Failure to follow this caution may result in damage to roof-
ing materials.
Membrane roofs can be cut by sharp sheet metal edges. Be
careful when placing any sheet metal parts on such roof.
WARNING
PERSONAL INJURY HAZARD
Failure to follow this warning could cause personal injury.
For vertical supply and return units, tools or parts could drop
into ductwork and cause an injury. Install a 90 degree turn in
the return ductwork between the unit and the conditioned
space. If a 90 degree elbow cannot be installed, then a grille
of sufficient strength and density should be installed to pre-
vent objects from falling into the conditioned space. Due to
electric heater, supply duct will require 90 degree elbow.
NOTES:
1. SPREADER BARS REQUIRED FOR SIZES 07-14 — Top damage will occur if spreader bars are not used.
2. Dimensions in ( ) are in millimeters.
3. Hook rigging shackles through holes in base rail, as shown in detail “A.” Holes in base rails are centered around the unit center of gravity.
UNIT
MAX WEIGHT
DIMENSIONS
A
B
C
lb
kg
in.
mm
in.
mm
in.
mm
50TC-A07
1040
473
74.5
1890
38.0
965
41.5
1055
50TC-M08
1255
569
88.0
2235
40.0
1015
41.5
1055
50TC-M09
1305
592
88.0
2235
39.5
1005
49.5
1255
50TC-M12
1400
635
88.0
2235
41.0
1040
49.5
1255
50TC-D/E08
1410
641
88.0
2235
41.0
1040
41.5
1055
50TC-D/E09
1525
693
88.0
2235
40.5
1030
49.5
1255
50TC-D/E12
1565
711
88.0
2235
40.0
1015
49.5
1255
50TC-D/E14
1720
782
88.0
2235
28.5
725
53.0
1345
50TC-D/E16
2010
912
116.0
2945
57.5
1461
59.5
1510
DETAIL "A"
PLACE ALL SEAL STRIP IN PLACE
BEFORE PLACING UNIT ON ROOF CURB.
DUCT END
SEE DETAIL "A"
"A"
(914-1371)
36"- 54"
"C"
"B"
SPREADER
BARS
REQUIRED
Summary of Contents for WeatherMaker 50TC07 Series
