![background image](http://html1.mh-extra.com/html/carrier/niceday-42phq/niceday-42phq_owners-manual_2561401010.webp)
GB - 9
42PHW / 42PHQ / 42PHQ...K
E N G L I S H
Cancellation of ON, OFF and EVERYDAY
timer procedure
1.
Press the ON TIMER button to cancel the
ON Timer or press OFF TIMER button to
cancel the OFF timer.
To cancel the EVERYDAY timer
setting, press the EVERYDAY, ON
TIMER or OFF TIMER button.
2.
Press the CANCEL button by pointing the
remote control towards the receiver of the
indoor unit.
• A receiving beep is heard.
• The orange light of the indoor unit switches off.
Sleep timer button (button L)
Press this button to set the SLEEP timer.
SLEEP timer procedure
If you want to stop the operation after 3 hours from the current time.
1.
Press the SLEEP button 3 times.
• 3:hr will be displayed and the
signal will be flashing.
• After 5 seconds, the stop time will be
displayed.
• The unit operates in sleep mode for 3
hours and will stop operation at the end of
the 3 hours.
• To change the reserved time or to cancel,
press the SLEEP button again.
1:hr 2:hr 3:hr 7:hr 9:hr Cancel
2.
When the SLEEP timer is set, the unit will
control the set temperature to avoid
overcooling or overheating during operation.
The set temperature is changed as follows:
Use of the remote control
A
A
A
A
Current time adjusting and reset buttons
(buttons M)
Press current time adjusting button "TA" to adjust the current time.
Press reset button "RST" if the remote control is not operating
properly or after replacing the batteries.
Setting current time
1.
Press the TA button with a sharp
object and the current time
indication symbol flashes.
At the start 6:00 A.M. will flash.
2.
Set the current time with the
hour and the minute buttons
while the current time indication
flashes.
3.
Press the TA button again.
The flashing will stop and the
current time will be set.
Address switch (button N)
If you have two indoor units in the same room, you can link one
remote control to one indoor unit, and the other remote control to
the other indoor unit.
Matching address between indoor unit and
remote control
1.
When two units are used in the same room, you can match the
address of the remote control to that of the unit.
2.
Remove the lid of the battery case.
Assign the address switch of one remote control to B.
Press the RST button with a sharp object.
3.
Turn off the unit and pull out the power plug.
Remove the front panel, teminal block cover, and frame grille.
Pull out the PCB.
Assign the address switch of one indoor unit to B.
SLEEP
TEMP.
CLOCK EVERYDAY
MINUTE
HOUR
MODE
ON
OFF
TIMER
CANCEL
SET
TA
RST
I / O
FAN
FLAP
SLEEP
TEMP.
CLOCK EVERYDAY
MINUTE
HOUR
MODE
ON
OFF
TIMER
CANCEL
SET
TA
RST
I / O
FAN
FLAP
SLEEP
TEMP.
CLOCK EVERYDAY
MINUTE
HOUR
MODE
ON
OFF
TIMER
CANCEL
SET
TA
RST
I / O
FAN
FLAP
+0.5
°
C
+0.5
°
C
+0.5
°
C
+0.5
°
C
°
C
30 70 110 150
(For Cooling or Dehumidification mode)
(For Heating mode)
SET
TEMP.
SET
TEMP.
SET TIME
SET TIME
TIME (MIN.)
TIME (MIN.)
SLEEP
-1
°
C
°
C
30 90 150
-1
°
C
-1
°
C