Carrier MMU-AP0072H2UL Installation Manual Download Page 11

– 10 –

EN

Power supply wire

• Recommended wire diameter and wire length for power supply wire.

Electric characteristics

Control wire

Remote control wiring

• 2-core with non-polarity wire is used for wiring of the remote control wiring and group remote controls wiring.

CAUTION

The remote control wire (Communication line) and AC208/230 V wires cannot be parallel to contact each other and 
cannot be stored in the same conduits. If doing so, a trouble may be caused on the control system due to noise or other 
factor.

NOTE

• Use copper supply wire.
• Use UL wire rated 600 V for the power supply.
• Use UL wire rated 300 V for the remote control wires and control wires.

Power supply wiring

Wire size: 2 

×

 AWG12

Ground

×

 AWG12 or thicker

Up to 164’1” (50 m)

MCA : Minimum Circuit Amps

MOCP : Maximum Overcurrent Protection (Amps)

Model

Power Supply

Voltage Range (V)

MCA

MOCP

Min

Max

(A)

(A)

MMU-AP0072H2UL

208/230 V-1-60 Hz

187

253

0.8

15

MMU-AP0092H2UL

0.8

15

MMU-AP0122H2UL

0.8

15

MMU-AP0152H2UL

0.8

15

MMU-AP0182H2UL

0.8

15

MMU-AP0212H2UL

1.0

15

MMU-AP0242H2UL

1.0

15

MMU-AP0302H2UL

1.0

15

MMU-AP0362H2UL

1.3

15

MMU-AP0422H2UL

1.3

15

Control wiring between indoor units, and outdoor unit (2-core 

shielded wire)

Wire size

(Up to 3280’10” (1000 m)) AWG16

(Up to 6561’8” (2000 m)) AWG14

Remote control wiring, remote control inter-unit wiring

Wire size: AWG20

Total wire length of remote control wiring and remote control 

inter-unit wiring = L + L1 + L2 + … Ln

In case of wired type only

Up to 1640’5” (500 m)

In case of wireless type included

Up to 1312’4” (400 m)

Total wire length of remote control inter-unit wiring = L1 + L2 + … Ln

Up to 656’2” (200 m)

L1

L

L2

Ln

Indoor unit

Remote control inter-unit wiring

Indoor unit

Indoor unit

Indoor unit

Remote

control

(Max. 8 units)

Remote 

control 

wiring

Wiring between indoor and outdoor units

NOTE

An outdoor unit connected with control wiring between indoor and outdoor units wire becomes automatically the header 
unit.

Wiring example

U1U2

U1U2U3U4

L1 L2 L3 N

U5U6

L1L2

A B

U1U2

L1L2

A B

U1U2

L1L2

A B

U1U2

L1L2

A B

A B

U1U2U3U4

L1 L2 L3 N

U5U6

A B

A B

Outdoor Power supply

Ground

terminal

Ground

terminal

Outdoor Power supply

Circuit breaker

Circuit breaker

Header outdoor unit

Follower outdoor unit

Control wiring between outdoor units

Control wiring between indoor and outdoor units

Control wiring between indoor units

Indoor unit

Indoor unit

Indoor unit

Indoor unit

Ground

Ground

Ground

Ground

Remote 

control

Remote 

control

Remote 

control

Indoor 

power 

supply

Circuit 

breaker

208/230-3-60

460 V -3 - 60 Hz

208/230-3-60

460 V -3 - 60 Hz

208/230-

1-60

Disconnect 

switch per NEC

Disconnect 

switch per 

NEC

Disconnect 

switch per 

NEC

Disconnect 

switch per 

NEC

19-EN

20-EN

+00EH99876001-3.book  Page 10  Wednesday, May 27, 2015  10:08 AM

Summary of Contents for MMU-AP0072H2UL




















Reviews: