background image

3.1

95-8600

10

DEVICE REPAIR AND RETURN

Prior to returning devices, contact the nearest local 

Detector Electronics office so that a Return Material 

Identification (RMI) number can be assigned.  

written statement describing the malfunction must 
accompany the returned device or component to 
assist and expedite finding the root cause of the 
failure.

Pack the unit properly.  Always use sufficient packing 

material.  Where applicable, use an antistatic bag as 

protection from electrostatic discharge.

NOTE

Det-Tronics reserves the right to apply a service 
charge for repairing returned product damaged as 
a result of improper packaging.

Return all equipment transportation prepaid to the factory 

in Minneapolis.

ORDERING INFORMATION

When ordering, please specify:
xWatch Explosion Proof Camera Model X7050
Refer to the xWatch Model Matrix below for details.

ACCESSORIES
Swivel Mount Bracket

 is required for mounting the 

camera:

 

Q9001B1175 Aluminum Mounting Bracket 

 

  (p/n 002099-003)

 

Q9001H8001 Stainless Steel Mounting Bracket 

  (p/n 004404-002)

Q1201A Laser Holder/Laser

 is used for sighting the 

flame detector and xWatch Camera.  The Laser Holder 

easily attaches to the front of the detector or camera.  

The Laser projects a red laser beam to show the exact 

center of the field of view.  Additional laser positions are 

provided to show the outside edges of the field of view.

REPLACEMENT PARTS
Part Number  Description

009448-003 

Model DE2020N –  

 

Replacement Camera Module, 2.33 mm, NTSC

009448-004 

Model DE2020P –  

 

Replacement Camera Module, 2.33 mm, PAL 

009448-005 

Model DE2022N –  

 

Replacement Camera Module, 4.3 mm, NTSC

009448-006 

Model DE2022P –  

 

Replacement Camera Module, 4.33 mm, PAL

009448-007 

Model DE2023N –  

 

Replacement Camera Module, 8.0 mm, NTSC

009448-008 

Model DE2023P –  

 

Replacement Camera Module, 8.0 mm, PAL

107427-004 

Rubber O-rings

001680-001 

Window cleaner squeeze bottle  

 

(package of six bottles)

005003-001  

Silicone-free grease

ASSISTANCE

For assistance in ordering a system to meet the needs of 

a specific application, contact:
Detector Electronics Corporation

6901 West 110th Street

Minneapolis, Minnesota  55438  USA

Operator:  (952) 941-5665 or (800) 765-FIRE

Customer Service:  (952) 946-6491

Fax:  (952) 829-8750

Web site:  www.det-tronics.com

E-mail:  [email protected]

Summary of Contents for DET-TRONICS xWatch X7050

















Reviews: