8
Introduction
Models C708/C709/C716/C717
General Installation Instructions
The following are general installation instructions.
For complete installation details, please see the
check out card.
Disconnect Switch
If the unit has no plug, a separate disconnect switch
must be installed, or another alternate means to
disconnect power must be implemented.
Air Cooled Units
C708 & C709:
These units require a minimum of 6”
(152 mm) air clearance on both sides, and the back
of the unit placed against the wall to prevent
recirculation of warm air. An optional air discharge
chute is available to direct heated air exhaust
upward. No clearance is required on the right side if
the air discharge chute is used.
C716 & C717:
These units require a minimum of 3”
(76 mm) air clearance around all sides. Install the
deflector provided to prevent recirculation of warm
air.
Refrigeration
Main Compressor:
Air cooled units:
40 oz (1,134 g) of R404A.
Water cooled units: 38 oz (1,077g) of R404A.
Gear Alignment and Rear Shell Bearing
1.
Make certain the drive shaft(s) can easily slide
in and out of the female socket on the gear
unit(s).
2.
If a drive shaft is binding, the gear unit could be
out of alignment (loose). Check the bolts on the
gear unit to be sure they are tight.
3.
Inspect the rear shell bearing for tightness. Be
sure the locking tab has been folded over to
prevent the nut from loosening.
Beater Rotation
REMEMBER TO DISCONNECT ALL
POWER TO THE FREEZER!
Failure to follow this
instruction may result in electrocution or severe
personal injury from hazardous moving parts.
1.
Remove the door assembly, beater and scraper
blades.
2.
Place a magnet over the door switch in the
front panel. This deactivates the safety feature
which prevents the operation of the machine
when the door is not installed.
3.
Place the power switch in the ON position.
4.
Press the WASH symbol on the control panel.
This activates the beater motor only.
5.
Look into the freezing cylinder. The drive shaft
should be turning clockwise. (If necessary, lift
the swing panel to view rotation.)
6.
Press the WASH symbol again to stop the
beater motor.
Note:
Repeat these steps for the other side on the
model C716 & C717.
To correct rotation on a single-phase unit, exchange
leads inside the beater motor. (Follow the diagram
printed on the motor.)
To correct rotation on a three-phase unit,
interchange any two incoming power supply lines at
freezer main terminal block only.
REMEMBER TO DISCONNECT ALL
POWER TO THE FREEZER!
Failure to follow this
instruction may result in electrocution or severe
personal injury from hazardous moving parts.
Summary of Contents for C708
