background image

52S

SERIES

4

VOLTAGE SUPPLY

Check voltage supply at outlet. For satisfactory re-
sults, the voltage range must always be within the 
ranges found on the data information plate
(Figure 1).

■  

208/230-v CORD-CONNECTED UNITS

 — The field-

supplied outlet must match the plug and be within 
reach of the service cord. Refer to Table 2 for proper 
receptacle and fuse type.

TABLE 2 — RECEPTACLES AND FUSE TYPES,

 250 VOLTS

LEGEND

HACR —

 Heating, Air Conditioning, Refrigeration 

*May be used for 15-amp applications if fused for 15 amp.

■  

265-v ACCESSORY CORD-CONNECTED UNITS — 

The field-supplied outlet must match the plug and be 
within reach of the service cord. Refer to Table 3 for 
the proper receptacle and fuse type.

TABLE 3 — RECEPTACLES AND FUSE TYPES,

265 VOLTS

LEGEND

HACR —

 Heating, Air Conditioning, Refrigeration 

*May be used for 15-amp applications if fused for 15 amp.

LOW-VOLTAGE CONNECTIONS — 
REMOTE CONTROL AND ENERGY 
MANAGEMENT ACCESSORY

Energy Management Accessory must be ordered sepa-
rately and field-installed. Low-voltage connections 
must be made for Energy Management Units. Refer to 
page 10.
Remote control units are supplied with a low-voltage 
terminal board for direct interface with a field-
supplied low-voltage, manual changeover thermo-
stat or a programmable thermostat (both are
Manufacturer-recommended). When properly wired, 
the unit operation is controlled by either wall-mounted 
thermostat.

RATED VOLTS

250

AMPS

15

20

30

BLADE CONFIGURATION

MFG PART NO.

Hubbell

5661

5461

8330

P & S

5661

5871

5930

GE

GE4069-1

GE4182-1

GE4139-3

Arrow-Hart

5661

5861

5700

TIME-DELAY TYPE
FUSE 

(or HACR Circuit 
Breaker)

15

20*

30

RATED VOLTS

265

AMPS

15/20

30

BLADE CONFIGURATION

MFG PART NO.

Hubbell

9315

Eagle

834B-BOX

TIME-DELAY TYPE FUSE

 (or HACR Circuit Breaker)

20*

30

IMPORTANT: The 265-v cord-connected units re-
quire an accessory subbase, Part No. SUB-BASE, 
with a field-installed receptacle. See Table 3 and 
Figure 4. 

FIGURE 4 — SUBBASE ASSEMBLY

Summary of Contents for 52SC





















Reviews: