Carrier 50TCQD17-D24 Service And Maintenance Instructions Download

Page: 1 / 60

50TCQD17---D24

Single Package Heat Pump/Electric Heat

Nominal 15 to 20 Tons

With Puron



(R---410A) Refrigerant

Service and Maintenance Instructions

TABLE OF CONTENTS

SAFETY CONSIDERATIONS

. . . . . . . . . . . . . . . . . . . .

UNIT ARRANGEMENT AND ACCESS

. . . . . . . . . . .

SUPPLY FAN (BLOWER) SECTION

. . . . . . . . . . . . . .

HEAT PUMP REFRIGERATION SYSTEM

. . . . . . . . .

THERMOSTATIC EXPANSION VALVE (TXV)

. . . .

PURON

(R--410A) REFRIGERANT

. . . . . . . . . . . . .

COOLING CHARGING CHARTS

. . . . . . . . . . . . . . . .

CONVENIENCE OUTLETS

. . . . . . . . . . . . . . . . . . . .

HEAT PUMP CONTROLS

. . . . . . . . . . . . . . . . . . . . . .

PROTECTIVE CONTROLS

. . . . . . . . . . . . . . . . . . . . .

COMMERCIAL DEFROST CONTROL

. . . . . . . . . . .

ELECTRIC HEATERS

. . . . . . . . . . . . . . . . . . . . . . . . .

SMOKE DETECTORS

. . . . . . . . . . . . . . . . . . . . . . . . .

PREMIERLINK



CONTROL

. . . . . . . . . . . . . . . . . . .

RTU--OPEN CONTROL SYSTEM

. . . . . . . . . . . . . . . .

SENSORY/ACCESSORY INSTALLATION

. . . . . . . .

ADDITIONAL RTU--OPEN INSTALLATION AND

TROUBLESHOOTING

. . . . . . . . . . . . . . . . . . . . . . . . .

PRE--START--UP

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

START--UP

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

START--UP, GENERAL

. . . . . . . . . . . . . . . . . . . . . . . .

START--UP, PREMIERLINK



. . . . . . . . . . . . . . . . . . .

START--UP, RTU--OPEN

. . . . . . . . . . . . . . . . . . . . . . . .

FASTENER TORQUE VALUES

. . . . . . . . . . . . . . . . .

APPENDIX I. MODEL NUMBER SIGNIFICANCE

APPENDIX II. PHYSICAL DATA

. . . . . . . . . . . . . . . .

APPENDIX IV. WIRING DIAGRAMS

. . . . . . . . . . . .

APPENDIX V. FAN PERFORMANCE

. . . . . . . . . . . .

APPENDIX VI. MOTORMASTER SENSOR LOCA-

TIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

START-UP CHECKLIST

. . . . . . . . . . . . . . . . . . . . . . .

SAFETY CONSIDERATIONS

Installation and servicing of air-conditioning equipment

can be hazardous due to system pressure and electrical

components. Only trained and qualified service personnel

should install, repair, or service air-conditioning

equipment. Untrained personnel can perform only the

basic maintenance functions such as replacing filters.

Trained service personnel should perform all other service

and maintenance operations.

When working on air-conditioning equipment, observe

precautions in the literature, tags and labels attached to

the unit, and other safety precautions that can apply.

Follow all safety codes. Wear approved safety glasses and

leather work gloves. Use quenching cloth for unbrazing

operations. Have fire extinguishers available for all

brazing operations.

Read these instructions thoroughly and follow all

warnings or cautions attached to the unit. Consult local

building codes and National Electrical Code (NEC) for

special requirements.

Recognize safety information. This is the safety--ALERT
symbol

. When you see this symbol on the unit and in

instructions or manuals, be aware of the potential for

physical injury hazards.

Understand the signal words

DANGER

WARNING

, and

CAUTION

. These words are used with the safety--ALERT

symbol.

DANGER

indicates a hazardous situation which,

if not avoided,

will

result in death or severe personal

injury.

WARNING

indicates a hazardous situation which,

if not avoided,

could

result in death or personal injury.

CAUTION

indicates a hazardous situation which, if not

avoided,

could

result in minor to moderate injury or

product and property damage.

NOTICE

is used to address

practices not related to physical injury.

NOTE

is used to

highlight suggestions which

will

result in enhanced

installation, reliability, or operation.

Summary of Contents for 50TCQD17-D24





























































Search results

Summary of Contents for 50TCQD17-D24

Reviews:

Related manuals for 50TCQD17-D24

Brands by name

Popular brands

Carrier 50TCQD17-D24, Service And Maintenance Instructions

Search results

Summary of Contents for 50TCQD17-D24

Reviews:

Related manuals for 50TCQD17-D24

Brands by name

Popular brands