Carrier 50HB Manual Download Page 5

5

Horizontal package air conditionners

4. S

AFETY ADVICE

V-220005

V-220004

To avoid any risk of accident during installation, commissioning or 
maintenance, it is obligatory to take into consideration the following 
speci

 cations for the units: refrigerated circuits under pressure, refrigerant 

presence, electrical voltage presence and implantation place.
Because of all of this, only quali

 ed and experienced personnel can 

perform maintenance tasks or unit repairs. 

It is required to follow the recommendations and instructions 
in the maintenance brochures, the labels, and the speci

 c 

instructions.
It is necessary to comply with the norms and regulations in 
effect. It is recommended to consult the competent authorities 
regarding the applicable regulations for users of units or 
components under pressure. The characteristics of these units 
or components are included on the plates of characteristics 
or in the regulatory documentation provided with the product.

The compressor and line surfaces can reach temperatures 
above 100ºC causing burns to the body. In the same fashion, 
under certain conditions these surfaces can reach very cold 
temperatures that can cause freezing risks.
Use safety goggles and gloves on the job. Be careful with 
sharp parts or elements in the unit. 

Caution:

Before intervening in the unit, verify that the main 

power to the unit is cut off. An electric shock can cause 
personal damage.

Note:

 In order to recycle these units follow the stipulations 

of Directive 2012/19/EU on

 Waste electrical and electronic 

equipment

 (WEEE).

These units work with refrigerant gas 

R-410A

.

In case of a leak:
-  Toxicity: According to ASHRAE 34, R-410A belongs to the A1/A1 group, 

i.e. with high safety both in the mix and also in the case of a leak. 

-  Although it is not toxic, in case of a leak to atmospheric pressure the 

liquid phase evaporates. The resulting vapours are heavier than air 
and can displace the technician local air. In case of an accidental 
discharge in a closed enclosure, fans must be used to eliminate said 
vapours.

-  Although the R-410A is not 

 ammable, when in contact with a 

 ame 

o hot spot it can decompose in 

 uorhydric acid HF and 

 uophosgene 

COF

2

 highly toxic and corrosive.

-  To detect leaks, an electronic leak detector, an ultraviolet lamp or 

soapy water must be used. Flame detectors do not help.

Important

: Immediately repair any refrigerant leak, using 

a recovery unit speci

 c for R-410A that avoids a possible 

mixture of refrigerants and/or oils.

Refrigerant leaks:

A periodical check must be performed for refrigerant gas leaks as 
per Regulation (EC) Nº517/2014 over 

certain greenhouse effect 

 uoride gases. 

Please, consult the frequency of checks in chapter 

of “Maintenance”.

Components of the R-410A

R-32

R-125

Chemical formula

CH2F2

CHF2CF3

Weight ratio

50%

50%

Unitary global warming potential (GWP) 

675

3.500

Global warming potential (GWP) 

2.088

 Note: 

The serial number must be used in all correspondence 

regarding the unit.

All units bear, legibly and indelibly, a data plate located in a prime space, 
as appears in the attached image: Check that this plate matches the 
correct model.

5. U

NIT IDENTIFICATION

Check the condition of the equipment upon delivery. 

Check that the details on the label, the packing and the data plate match 
the order. If equipment has been damaged, or there is a shortfall in 
delivery, notify accordingly.

Ref\Reference

No Serie\serial Nbr.

Año\An.Year

Producto\Product\Produit

Ref. Produit\Item Nbr

Max.Intensidad\Intensité\Current

Kit Elec.

Tension\Voltage

Refrig.KG (Fábrica\Factory\Usine)/Co2 Teq.

Refrigerant

NoBo

Peso\Poids\Weight

PSmax(AP\HP)

Temp. Max./ IP

PSmax(BP\LP)

Fabricante\Fabricant\Manufacturer:
Compañía Industrial de Aplicaciones Térmicas, S.A.
P. Ind. Llanos de Jarata s/n. 14550 Montilla-SPAIN

Contient des gaz à effet de serre fluorés \ Contains fluorinated greenhouse gases regulated by the Kyoto protocol

Contiene gases fluorados de efecto invernadero regulados por el protocolo de Kyoto

1

16

2

3

4

5

6

7

8

9

10

11

12

13

14

15

17

CARRIER SCS
Route de Thil

01122 Montluel-FRANCE

Legend 

1

Year of manufacture

2

Commercial product name

3

Serial number

4

Description of the product

5

Purchase order number 

6

Sales order number 

7

Work order number

8

Power supply

9

Power output of the auxiliary electrical heaters kit (optional) (kW)

10

Maximum absorbed current under full load (A) ( including the electrical kit)

11

Type of refrigerant

12

Refrigerant content (kg) and Environment impact (CO

2

 Teq.)

13

Maximum service pressure in the high pressure side (R-410A = 42 bar) 

14

Maximum service pressure in the low pressure side (R-410A = 24 bar) 

15

Maximum operating temperature (refer to “Opration limits”)

Maximum shipment and storage temperature: +50ºC

Electrical protection rating: IP54 

16

Operation weight (kg) (empty  

 uid + refrigerant)

17

Noti

 ed Body number for surveillance of the Pressure Equipment Directive

Summary of Contents for 50HB





















Reviews: