manualshive.com logo in svg

Carrier 50HB, Manual

Share
Download
Carrier 50HB Manual Download Page 12

12

Horizontal package air conditionners

Access for maintenance:

The frame has access designed from the right side for maintenance. 

To access the electrical 
heaters, the screws that 
fasten the frame side panel 
must be unscrewed as shown 
in the illustration.

Access panel

Electrical heater

-  The auxiliary electrical heaters are ready for operation in one power 

stage. 

-  The heaters acquired with the unit will be incorporated to it modifying 

the electric panel in the factory, so that it is compatible with the 
electronic control.

-  The electrical heaters requested for units already shipped will be 

sent in a kit, and the installer will need to assemble the elements 
required for the operation of the unit and for compliance with the 
legal regulations that are applied to the modi

fi

 ed unit with regard to 

safety.

Note: with this option, the air 

fl

  ow controller is included.

9. O

PTIONS

Condensation pressure control

This control is advisable for units that work in cooling with an outdoor 
temperature below 15º C. 
In units with centrifugal fan a check is performed per damper in the 
fan outlet. A servomotor opens or closes the damper depending on the 
proportional signal 0-10V received from the electronic control system.

Clogged 

fi

 lter detector

Differential pressostat for indication of maintenance to 

fi

 lters. Automatic 

reactivation.
This pressostat is installed in the auxiliary electric panel. 

Air

fl

 ow control

Differential pressostat that measures the 

fl

 ow variation in the air supply. 

This allows the detection of fan belt breakages, since the fan relay only 
detects operating faults that have arisen in the motor. 
This pressostat is installed in the auxiliary electric panel. 
This safety device is compulsory in units with electrical heaters. 

Auxiliary

electric panel

Pressostat for 

dirty

fi

 lters

Pressostat for 

fl

 ow control

Filters

These units can substitute the 

fi

 ltering mesh that the units include 

regularly with G4 rating, mounted on the same frame.
This frame can be extracted easily by both sides.

Frame in displacement

Servomotor

Damper

Summary of Contents for 50HB





















Reviews:

No comments

Brands by name

Popular brands

Load more brands