6
Table 1 — VAV-RTU Open Inputs and Outputs
(1) Safety Chain Feedback: 24Vac required at this terminal to provide “Run Enable” status. See Input/Output section for additional instructions.
(2) These inputs are configurable. If installed, they take the place of the default input on the specific channel. See appropriate Input Configuration Sec-
tion for wiring and setup instructions.
(3) Parallel pins J5 - 1 = J2 - 6, J5 - 3 = J1 - 10, J5 - 5 = J1 - 2 are used for field installation.
(4) Refer to the input configuration and accessory sections for more detail.
POINT NAME
BACnet OBJECT NAME
TYPE OF I/O
CONNECTION PIN
NUMBER(S)
CHANNEL DESIGNATION
DEDICATED INPUTS
Return Air Temperature
ra_temp
AI (10K Thermistor)
J20- 3 and 4
Analog Input 11
Space Temperature
n/a
AI (10K Thermistor)
J20-1 and 2
Analog Input 10
Supply Air Temperature
sa_temp
AI (10K Thermistor)
J2- 1 and 2
Analog Input 6
Outdoor Air Temperature
oa_temp
AI (10K Thermistor)
J2- 3 and 4
Analog Input 7
Static Pressure Sensor
static_press
AI (4- 20 mA)
J4- 4 and 5
Analog Input 1
Safety Chain Feedback
safety_status
BI (24 VAC)
J1- 9
Binary Input 4
Compressor Safety Status
(1)
comp_status
BI (24 VAC)
J1- 2
Binary Input 3
Fire Shutdown Status
firedown_status
BI (24 VAC)
J1- 10
Binary Input 5
Enthalpy Status
enthalpy_status
BI (24 VAC)
J2- 6 and 7
Binary Input 8
Zone Temperature
n/a
n/a
J13- 1- 4
Rnet
CONFIGURABLE INPUTS
(4)
Indoor Air CO
2
iaq
AI (4- 20 mA)
J4-2 and 3
Analog Input 2
Outdoor Air CO
2
oaq
AI (4-20 mA)
Space Relative Humidity
space_rh
AI (4- 20 mA)
Supply Fan Status
(2)
sfan_status
BI (24 VAC)
J5-1 and 2 or J5-3 and 4,
J5
-
5 and 6 or J5-7 and 8
(3)
Binary Input 3, 5, 8, or 9,
except where intrinsic input
is used
Filter Status
(2)
filter_status
BI (24 VAC)
Binary Input 3, 5, 8, or 9,
except where intrinsic input
is used
IGC Override
(2)
igcovr_status
BI (24 VAC)
Binary Input 9. Mandatory
input on gas heat units.
OUTPUTS
Economizer Output
econ_output
AO (4-20mA)
J2- 4 and 5
Analog Output 1
Supply Fan VFD
vfd_output
AO (2- 10Vdc)
J22- 1 and 2
Analog Output 2
Supply Fan Relay State
sfan
BO Relay (24VAC, 1A)
J1- 4
Binary Output 1 (G)
Cool Stage 1 Relay State
comp_1
BO Relay (24VAC, 1A)
J1- 8
Binary Output 5 (Y1)
Cool Stage 2 Relay State
comp_2
BO Relay (24VAC, 1A)
J1- 7
Binary Output 4 (Y2)
Cool Stage 3 Relay State
comp_3
BO Relay (24VAC, 1A)
J11- 5 and 6
Binary Output 7 (Y3)
Heat Stage 1 Relay State
heat_1
BO Relay (24VAC, 1A)
J1- 6
Binary Output 3 (W1)
Heat Stage 2 Relay State
heat_2
BO Relay (24VAC, 1A)
J1- 5
Binary Output 2 (W2)
Power Exhaust Relay State
pexh
BO Relay (24VAC, 1A)
J11-2 and 3 (N.O.)
Binary Output 8 (PE)
Heat Interlock Relay State
ht- interlock
BO Relay (24VAC, 1A)
J11
-
7 and 8
Binary Output 6 (HIR)
Summary of Contents for 48LCB07
