Carrier 48LCB07 Controls, Start-Up, Operation And Troubleshooting Download | Manualshive

Page: 1 / 60

background image

Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.

Catalog No. 04-53480277-01

Printed in U.S.A.

Form 48-50LCB-7-26-02T Rev. A

Pg 1

3-2020 Replaces: 48-50LCB-7-26-01T

Controls, Start-Up, Operation and

Troubleshooting

CONTENTS

Page

SAFETY CONSIDERATIONS   . . . . . . . . . . . . . . . . . . . 2
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
SENSOR/ACCESSORY INSTALLATION  . . . . . . . . . . 3
Sensors and Accessories   . . . . . . . . . . . . . . . . . . . . . 7
User Interfaces   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Install Analog Sensors  . . . . . . . . . . . . . . . . . . . . . . . . 7

• SUPPLY AIR SENSOR (SAT)

• OUTDOOR AIR SENSOR (OAT)

• CO2 SENSOR(S) (IAQ AND OAQ)

• RELATIVE HUMIDITY SENSORS (SPACE OR DUCT

Installing Discrete Inputs . . . . . . . . . . . . . . . . . . . . . 14

• SINGLE ENTHALPY (OUTDOOR ENTHALPY)

• DIFFERENTIAL ENTHALPY

• FIRE SHUTDOWN

• FILTER STATUS

• IGC OVERRIDE

Communication Wiring . . . . . . . . . . . . . . . . . . . . . . . 15

• BACNET MS/TP

• I-VU BUILDING AUTOMATION SYSTEM

• LOCAL ACCESS

START-UP   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
VAV-RTU Open System Start-Up  . . . . . . . . . . . . . . . 17
Additional Installation/Inspection  . . . . . . . . . . . . . . 17

• POWER EXHAUST RELAY POWER

Service Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

• COMPRESSOR 1 AND COMPRESSOR 2 TEST

• HEAT 1 AND HEAT 2 TEST

• POWER EXHAUST TEST

• ECONOMIZER TEST

• VFD SPEED TEST

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

• UNIT CONFIGURATION

• SERVICE CONFIGURATION

LINKAGE BASED OPERATION . . . . . . . . . . . . . . . . 22
Occupancy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Indoor (Supply) Fan . . . . . . . . . . . . . . . . . . . . . . . . . 22

• FAN OFF DELAY

• INDOOR (SUPPLY) FAN STATUS

Cooling  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Supply Fan  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Economizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Enthalpy Control   . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Space Air Quality  . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Power Exhaust  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Heating  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

• MORNING WARM-UP

• OCCUPIED HEATING

• UNOCCUPIED HEATING

Supply Air Tempering  . . . . . . . . . . . . . . . . . . . . . . . .24
Demand Controlled Ventilation   . . . . . . . . . . . . . . . .24
Demand Limit  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Unoccupied Free Cooling  . . . . . . . . . . . . . . . . . . . . .24
Fire Shutdown  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Compressor Safety  . . . . . . . . . . . . . . . . . . . . . . . . . .25
Fan Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Filter Status   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Linkage  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

• LINKAGE AIR SOURCE MODES

OPERATION — STANDALONE MODE . . . . . . . . . . .25
Occupied and Unoccupied Setpoints (standalone

mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25

Occupancy (using standalone configuration) . . . . .25
Indoor (Supply) Fan (standalone mode) . . . . . . . . .25

• FAN OFF DELAY

• INDOOR (SUPPLY) FAN STATUS

Cooling (standalone mode) . . . . . . . . . . . . . . . . . . . .26
Supply Fan (standalone mode) . . . . . . . . . . . . . . . . .26
Economizer (standalone mode) . . . . . . . . . . . . . . . .26

• ENTHALPY CONTROL

• SPACE AIR QUALITY

• POWER EXHAUST

Heating (standalone mode) . . . . . . . . . . . . . . . . . . . .27

• MORNING WARM-UP

• OCCUPIED HEATING

• UNOCCUPIED HEATING

• SUPPLY AIR TEMPERING

Demand Controlled Ventilation

(standalone mode) . . . . . . . . . . . . . . . . . . . . . . . . .28

Demand Limit (standalone mode)   . . . . . . . . . . . . . .28
Unoccupied Free Cooling (standalone mode)   . . . .28
Unoccupied Fan Cycling (standalone mode)  . . . . .28
Fire Shutdown (standalone mode)  . . . . . . . . . . . . . .28
Compressor Safety (standalone mode)  . . . . . . . . . .29

48/50LCB07-26

with VAV-RTU Open Controller

1
2
3
...
»

Summary of Contents for 48LCB07





























































Reviews:

No comments

Related manuals for 48LCB07

Brand: Daewoo Pages: 14

Brand: DAEWOO ELECTRONICS Pages: 18

Brand: Eaton-Williams Pages: 10

Brand: sans Pages: 16

Brand: KeepRite Pages: 16

Brand: Danby Pages: 26

VRV III BSVQ100P8V1B

Brand: Daikin Pages: 20

Brand: NewAir Pages: 15

Brand: Zibro Pages: 2

Brand: AIROCIDE Pages: 24

Brand: Oreck Pages: 46

OmniAire 2000C Series

Brand: Omnitec Pages: 9

Brand: Sinclair Pages: 38

Depuro Plus 230

Brand: Vortice Pages: 72

Suburban Dynaline 3 DYNA07AC

Brand: ACS Pages: 38

Brand: SCI Pages: 20

Brand: Envicool Pages: 31

Brand: Airwell Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands