EN
ES
FR
IT
DE
PT
PL
CZ
RU
CR
HU
TR
NL
GR
SV
FI
NO
DK
RO
BG
EE
LV
SK
SI
5
• Be sure to refer to the wiring system diagram labeled inside the front
panel.
• Check local electrical cords and also any speci
fi
c wiring instructions or
limitations.
NOTE
• Use stranded wire only.
• Wire type : More than 1.5 mm² (H07RN-F or 60245 IEC66) or 1.3 mm²
(AWG-16)
CAUTION
1. Open the air inlet grille upward.
2. Securely remove four screws at the front panel.
3. Slightly open the lower part of the front panel then pull the upper part of
the front panel toward you to remove it from the rear plate as shown on
fi
gure
1
.
4. After removing the front panel, remove the screws and Display unit from
the unit as shown on
fi
gure
2
then open the front cover of Display unit
as shown on
fi
gure
3
.
5. Arrange the control wire as detail and speci
fi
cation as shown on
fi
gure
4
.
6. Securely connect the control wire to terminal of Display unit board as
shown on
fi
gure
5
(tighten
fi
rmly but not over 0.12 N·m (0.01 kgf·m)).
7. Set the control wire throughout at slot on front cover of Display unit then
reassembly Display with main casing by reverse process of
fi
gure
2
and
3
. Make sure the control wire must not be pressed by front and rear
cover of Display unit.
8. Set the control wire out from indoor unit same portion as power supply
and connecting cable as shown on
fi
gure
6
.
9. Reassembly the indoor unit by reverse process of 1 to 3.
How to Connect Remote Controller
for Wire Operation
For indoor unit
Display board
2
3
Display unit
Remove screw
1. Remove cover of remote controller by sliding down and take it out.
2. If batteries are exist, please take them out. The combination of using
wire controller and batteries may cause of batteries explosion.
3. Make hole for insert control wire by use screwdriver break the polyester
sheet as shown on
fi
gure
7
.
4. Insert control wire from rear side of remote controller as shown on
fi
gure
8
.
5. Fix control wire which arrange as shown on
fi
gure
9
and
!
to terminal
by provided screws (tighten
fi
rmly but not over 0.25 N·m (0.03 kgf·m)).
6. Set control wire through gutter way at rear side of remote controller as
shown on
fi
gure
"
.
7. Fix provided screw (Ø3.1
×
16L) on the wall to hang remote controller as
shown on
fi
gure
#
.
8. Mark and arrange hole for
fi
x below screw (Ø3.1×25L) as shown on
fi
gure
#
.
9. Assembly battery cover which provided with accessory bag then use
provide screw (Ø3.1
×
25L) to
fi
x battery cover together with wall as
shown on
fi
gure
$
(tighten
fi
rmly but not over 0.15 N·m (0.02 kgf·m)).
10. Reassembly cover of remote controller.
For remote controller
* Wire size 28-22 AWG (0.08-0.32 mm
2
)
Outer diameter not over 4.7 mm,
control wire length 30 m or less.
70 mm
5 mm
4
6
5
Terminal
Control wire
Control wire out position
Control wire through out position
Tighten
fi
rmly but
not over 0.12 N·m
(0.01 kgf·m)
Control wire
7
8
Polyester sheet
close hole for insert
control wire
Control wire
9
!
Control wire
Terminal
* Wire size 28-22 AWG (0.08-0.32 mm
2
)
Outer diameter not over 4.7 mm,
control wire length 30 m or less.
30 mm
10 mm
Tighten
fi
rmly but not over
0.25 N·m (0.03 kgf·m)
1
2
3
Cord clamp
Terminal block
Terminal cover
Screw
Earth line
Screw
Connecting cable
Earth line
Connecting cable
Stripping length of the connecting cable
about 15 cm
110 mm
80 mm
20 mm
10 mm
Indoor unit
Control wire
Remote controller
Air inlet grille
Front panel
1
2
1
3
01_1115551229-EN.indd 5
01_1115551229-EN.indd 5
1/16/2558 BE 6:35 PM
1/16/2558 BE 6:35 PM
