manualshive.com logo in svg

Carrier 024-036, Service Manual, Page: 1 / 41

Share
Download
Carrier 024-036 Service Manual Download Page 1

Service Manual

Table of Contents

Safety Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Installation Guideline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Table 1 – Required Field-Installed Accessories for Air Conditioners 

and Heat Pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Low-Ambient Cooling Guideline . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Cabinet Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 2 – Defrost Control Speed-Up Timing Sequence  . . . . . . . 14

Scroll Compressor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Reciprocating Compressor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Refrigeration System  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table 3 – Compressor Information  . . . . . . . . . . . . . . . . . . . . . . . 21

Table 4 – Piston/TXV Table  . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Refrigeration System Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Table 5 – Minimum Airflow for Safe Electric Heater Operation 28

Table 6 – Superheat Charging . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 7 – 13.4 SEER2 Required Subcooling. . . . . . . . . . . . . . . . 29

ECM Fan Motor Troubleshooting  . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Care and Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Table 8 – Pressure vs. Temperature Chart -  R-410A Refrigerant38

024-048 A/C and 024-036 Heat Pump

A10165

060 A/C and 042-060 Heat Pump

A150067

Fig. 1 – A/C and Heat Pump

Safety Considerations

Installation, service, and repair of these units should be attempted only

by trained service technicians familiar with standard service instruction

and training material.
All equipment should be installed in accordance with accepted practices

and unit Installation Instructions, and in compliance with all national and

local  codes.  Power  should  be  turned  off  when  servicing  or  repairing

electrical  components.  Extreme  caution  should  be  observed  when

troubleshooting  electrical  components  with  power  on.  Observe  all

warning notices posted on equipment and in instructions or manuals.

Refrigeration  systems  contain  refrigerant  under  pressure.  Extreme

caution  should  be  observed  when  handling  refrigerants.  Wear  safety

glasses  and  gloves  to  prevent  personal  injury.  During  normal  system

operations, some components are hot and can cause burns. Rotating fan

blades can cause personal injury. Appropriate safety considerations are

posted throughout this manual where potentially dangerous techniques

are addressed.
Follow  all  safety  codes.  Wear  safety  glasses,  protective  clothing,  and

work gloves. Have a fire extinguisher available. Read these instructions

thoroughly and follow all warnings or cautions included in literature and

attached to the unit. Consult local building codes, the current editions of

the  National  Electrical  Code  (NEC)  NFPA  70  and  NFPA

90B-Installation Warm Air Heating and A/C Systems (Residential).
In Canada refer to the current editions of the Canadian Electrical Code

CSA C22.1.

Introduction

This  document  provides  required  system  information  necessary  to

install, service, repair or maintain the small package products (SPP)  air

conditioners and heat pumps using R-410A refrigerant.
Refer  to  the  unit  Product  Data/Technical  specifications  for  rating

information, electrical data,  required  clearances, additional component

Residential Mobile Home Small Package Products

Air Conditioners and Heat Pumps

Using R-410A Refrigerant

WARNING

!

UNIT OPERATION AND SAFETY HAZARD

Failure  to  follow  this  warning  could  result  in  personal  injury  or

equipment damage.

R-410A  systems  operate  at  higher  pressures  than  standard  R-22

systems. Do not use R-22 service equipment or components on these

R-410A units. Ensure service equipment is rated for R-410A.

WARNING

!

PERSONAL INJURY AND PROPERTY DAMAGE 

HAZARD

For continued  performance,  reliability, and safety, the  only  approved

accessories and replacement parts are those specified by the equipment

manufacturer.  The  use  of  non-manufacturer  approved  parts  and

accessories could invalidate the equipment limited warranty and result

in  fire  risk,  equipment  malfunction,  and  failure.  Please  review

manufacturer's  instructions  and  replacement  part  catalogs  available

from your equipment supplier.

Summary of Contents for 024-036










































Reviews:

No comments