manualshive.com logo in svg

Carrier 024-036, Service Manual, Page: 7 / 41

Share
Download
Carrier 024-036 Service Manual Download Page 7

: Service Manual

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

7

Access Compressor Or Other Internal Cabinet 

Components

NOTE: 

Access to most of the components through the side panels of the

unit.  The  top  will  need  to  be  removed  to  access  the  evaporator  or

condenser coil. In some instances screws on the back of the unit (duct

side) will need to be accessed. If the unit is up against the structure, the

unit will have  to be  pulled  away for  servicing.  Follow the procedures

below to access the different components:

1. Access  to  control  box,  compressor,  reversing  valve,  metering

device, accumulator and liquid line drier.

a. Removal of the right front panel, opposite the duct flanges will 

give access to the component above. (See 

Fig. 6

.)

2. Access to the indoor fan motor and electric heater

a. Removal of the right side (side with electric access), right back 

panel to access components above. (See 

Fig. 7

.)

3. Access or removal of the condenser coil.

a. Removal of the top, the control/compressor panel, the front/left 

side louver panel.

b. Screws from the compressor compartment and either the side of 

the unit or below the condenser fan (depending on the shape of 

coil) will need to be removed to remove condenser coil. (See 

Fig. 8

.)

4. Access or removal of the evaporator coil.

a. (024 to 036) The indoor evaporator coil is held in place by 

screws located in the compressor compartment and behind the 

return air duct.  The 14” return collar must be removed to access 

these screws.

b. (042 to 060)  The indoor evaporator coil is held in place by 

screws located in the compressor compartment and on the 

rectangular duct flange.  The rectangular duct flange does not 

need to be removed but the left side screws will have to be 

removed. (See 

Fig. 8

 and 

Fig. 9

.)

A10160

Fig. 6 – Removal of Right Front Panel

A10159

Fig. 7 – Removal of Right Side Back Panel

A10161

Fig. 8 – Access of Condenser Coil

A10173

Fig. 9 – Location of Screws

HEATER
PLUG

WIRE
TIES

EVAPORATOR

CONDENSOR

COILS

SMALL, MEDIUM CHASSIS

MEDIUM, LARGE CHASSIS

Summary of Contents for 024-036










































Reviews:

No comments