manualshive.com logo in svg

Carrier 024-036, Service Manual, Page: 3 / 41

Share
Download
Carrier 024-036 Service Manual Download Page 3

: Service Manual

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

3

Cabinet Assembly

Basic Cabinet Designs

Certain maintenance routines and repairs require removal of the cabinet

panels.  There are 3 cabinet sizes for the air conditioning and heat pump

models. However, all of the units have similar panel construction other

than their size. The base footprint is the same on all three cabinet sizes.

Door Gasket/Insulation:

If gaskets or insulation must be replaced, the materials must meet  the

original  equipment  specifications.  Insulation  must  meet  NFPA  90A

requirements for flame spread and smoke generation. Foam gaskets that

are in the conditioned air stream must meet the requirements of UL 94,

5VA for flammability.

Instructions for insulation installation: 

1. Apply adhesive on non-foil side of the insulation.
2. Align insulation to the panel. 
3. Care  must  be  taken  while  applying  the  adhesive,  so  it  does  not

come in contact with other non-insulated sheet metal surfaces.

4. Insulation must not contain any tears, voids, or bubbles after being

applied to access panel.

Fig. 2 – Cabinet Designs

Small, Medium and Large Cabinet

A10165

A10166

Small and Medium Cabinet

WARNING

ADVERTIS

SMENT

A10167

Medium and Large Cabinet Rear View

Summary of Contents for 024-036










































Reviews:

No comments