manualshive.com logo in svg

Carmanah SpeedCheck-18, User Manual, Page: 24 / 46

Share
Download
Carmanah SpeedCheck-18 User Manual Download Page 24

 

  

 

Carmanah Technologies Corp. | 250 Bay St, Victoria, BC V9A 3K5, Canada | 1.250.380.0052 | 

[email protected]

 | 

carmanah.com

     

24

 

SPEEDCHECK-15/18 USER MANUAL 

4.0 INSTALLATION 

 

3.  Attach solar panel to the 45-degree mount. Use bolts, washers, and locknuts that were supplied. Tighten 

nuts and bolts loosely

—

do not fully tighten

 at this stage. 

 

 

12.  Your system includes a cap for the open top of the pole. The cap prevents debris from entering 

the pole. There are plastic and metal versions of the cap: 

•

 

The plastic cap is inserted into the top of the pole prior to attaching the solar mount bracket. 

•

 

The metal cap is attached to the solar panel mounting bracket before the solar panel is 

mounted on the pole. Instructions are provided at the end of this section. 

 

 

4. 

PLASTIC CAP INSTALLATION (Standard Option)

: Fish solar panel harness through pole and plastic 

cap as shown. 

 

 

 

 

 

 

 

 

Summary of Contents for SpeedCheck-18















































Reviews:

No comments