background image

Model 99FRD, 100CRD & 102CRD oil burners — Instruction manual

Carlin part number MN99102 Rev. 08/20/08

– 28 –

For other than routine maintenance, contact 
a  qualified  service  company.  Perform  the 
following as needed.
•  Keep  the  area  around  the  burner  clear 

and  free  from  combustible  vapors  and 
liquids.

•  Do  not  obstruct  the  flow  of  combustion 

and ventilating air.

•  Most motors currently used on residential 

type burners use permanently-lubricated 
bearings, and do not require field lubri-
cation.  Read  the  label  on  the  motor  to 
determine  oiling  needs,  if  any.  Do  not 
over-lubricate. This can cause as much 
trouble as not lubricating at all.

  Never attempt to use gasoline as 

a fuel for this burner, as it is more 
combustible and could result in a 
serious explosion. Never attempt to 
burn refuse or use any fuel other 
than # 1 or # 2 heating oil (ASTM 

99FRD, 100CRD, and 
102CRD oil burner

User care and maintenance

  Refer only to the information on this 

page, intended for your use. The 
remainder of this manual is intended 
only  for  your  service  technician. 
Failure  to  comply  could  result  in 
severe  personal  injury,  death  or 
substantial property damage.

 

Should overheating occur:

 

(1) shut off the oil supply to the burner.

 

(2) DO NOT shut off the control switch to the 
circulator or blower.

 

(3) contact your oil dealer or service techni-
cian and the fire department (if needed).

 

The burner must be cleaned, tested 

and adjusted annually by a qualified oil 

burner service technician

.

Summary of Contents for 100CRD





























Reviews: