background image

Model 99FRD, 100CRD, & 102CRD oil burners — Instruction manual

Carlin part number MN99102 Rev. 08/20/08

– 27 –

Limited Warranty

Carlin Combustion Technology, Inc. (Carlin) warrants its products, to the original purchaser, to be 

free from defects in material and workmanship, under normal use and service for 36 months from 

the date of manufacture, except for commercial Products (over 3 GPH) that are warranted for 12 

months from the date of manufacture; and except for EZ-Pro™ Burners that are warranted for 36 

months from the date of manufacture, plus an extended period of two (2) additional years (total of 

five (5) years).

This warranty does not extend to equipment subjected to misuse, neglect, accident or 

water damage; nor does this warranty apply unless the product covered by it is properly 

installed by a qualified, competent technician, who is licensed where state or local codes 

require, and who is experienced in making such installations, in accordance with NFPA 

No. 31 of the National Fire Protection Association and in accordance with all applicable 

local, state and national codes.  Parts that are defective in material or workmanship and 

within the warranty period will be repaired or replaced as follows:

1.  Motors, fuel units, transformers and other non-Carlin products should be sent for repair or replace-

ment to an authorized service point or distributor of the manufacturer of such components when 

reasonably available in the Customer’s locality.

2.  Where such local service is not available with respect to the above listed components, or where 

Carlin components are involved, or for component parts of EZ-Pro Burners that fall within the 

extended warranty period, such defective parts should be returned, freight prepaid to Carlin.  

The repaired component or replacement part will be provided to the Customer freight prepaid 

by Carlin unless the returned part is determined by Carlin to be out of warranty or not to be 

defective, in which case it will be provided to the customer F.O.B., Carlin, East Longmeadow, 

Massachusetts.

3.  Contact Carlin Customer Service for warranty return procedures.
4.  The return of a burner is not covered by this warranty.  Contact Carlin Tech Service for assistance 

before replacing any burner.

5.  Carlin is not responsible for any labor cost for removal and replacement of equipment.
6.  Equipment that is repaired or replaced will carry the unexpired portion of the original equipment 

warranty.

7.  If inspection by Carlin does not disclose any defect covered by this warranty, the equipment may 

be repaired or replaced at the expense of the Customer, and Carlin’s regular charges will apply.

8.  Non-Carlin components are warranted for 12 months from date of installation or 18 months from 

date of manufacture, whichever date occurs first.

This warranty is limited to the precise terms set forth above, and provides exclusive rem-

edies expressly in lieu of all other remedies and in particular there shall be excluded the 

implied warranties of merchantability and fitness for a particular purpose.  In no event 

will Carlin Combustion Technology, Inc. be liable for any incidental or consequential 

damage of any nature.

  Carlin neither assumes nor authorizes any person to assume for Carlin 

any other liability or obligations in connection with the sale of this equipment.  Carlin’s liability and 

Customer’s exclusive remedy being limited to repairs or replacement as set forth above.

Summary of Contents for 100CRD





























Reviews: