Carl Valentin Dynacode II Series Operating Manual Download Page 62

Page: 62 / 122

Function Menu

Dynacode II Series

Operating Manual

08.16

9.14 Emulation

CVPL:

Carl Valentin Programming Language

ZPL:

Zebra

Programming Language

Change between CVPL protocol and ZPL II

protocol.

The direct print module performs a restart and ZPL II

commands are

transformed into CVPL commands internally by the direct print module
and then executed by the direct print module.

At activated ZPL II

emulation the printhead resolution of the emulated

direct print module must be set, e.g. 11.8 Dot/mm (= 300 dpi).

NOTICE!

If the printhead resolution of the Zebra

printer differs from that

of the Valentin device, then the size of objects (e.g. texts,
graphics) complies not exactly.

The access to Zebra

drives

B: CF card
R: RAM Disk (standard drive, if not indicated)

is rerouted to the corresponding Valentin drives
A: CF
R: RAM Disk

This can be necessary if the available space on the RAM disk (at
present. 512 KByte) is not sufficient or if bitmap fonts are downloaded
to the direct print module and be stored permanently.

NOTICE!

As the printer build-in fonts in Zebra

printers are not available

in Valentin devices, this can cause small differences in the text
image.

Protocol

Printhead resolution

Drive mapping

Summary of Contents for Dynacode II Series



























































































































Search results

Summary of Contents for Dynacode II Series

Reviews:

Related manuals for Dynacode II Series

Brands by name

Popular brands

Carl Valentin Dynacode II Series, Operating Manual

Search results

Summary of Contents for Dynacode II Series

Reviews:

Related manuals for Dynacode II Series

Brands by name

Popular brands