Carl Valentin Dynacode II Series Operating Manual Download Page 34 | Manualshive

Page: 34 / 122

background image

Installation and Initial Operation

Dynacode II Series

34

Operating Manual

08.16

7.1 Installation of Print Mechanics at Machines

NOTICE!

With the open printing unit (due to construction) the requirements
of EN60950-1 regarding fire protection casing are not fulfilled.
These must be ensured by the installation into the end device.

At the bottom of the mounting frame are two M8 threads that can be
used for the attachment at the machine. Additionally multi-functional
connecting parts are supplied.

Please observe the following conditions:



The maximum thread engagement of the M8 threads is 10 mm.



The print mechanics has to be installed with a distance from
printhead to brake stator of 1...2.5 mm (see illustration).

NOTICE!

A distance of 2 mm is recommended.



The best print results can be received if the silicon of the pressure
roll consists of a hardness of approx. 40° to 50 ° Shore A and/or
the elastometer of the counter-pressure plate shows a hardness
of approx. 60 ± 5 Shore A (ave

rage value of roughness Ra ≥ 3,2

mm).



The pressure roll/counter-pressure plate has to be installed
parallel to the linear movement of print unit and the focal line of
printhead. Discrepancies to the focal line and cavities in the print
surface can lead to an inferior print quality at these positions.

Figure 26

In case the machine is used without mounting frame, then it is
possible to fix the print module from the top with four M6 screws.

The maximum thread engagement of the M6 threads is 6 mm
(position of printhead see illustration).

Installation with
mounting frame

Installation without
mounting frame

«
...
32
33
34
35
36
...
»

Summary of Contents for Dynacode II Series



























































































































Reviews:

No comments

Related manuals for Dynacode II Series

Brand: BARMATIC Pages: 32

Brand: Gaggia Pages: 152

Brand: Fagor Pages: 21

Brand: Fagor Pages: 29

Brand: Fagor Pages: 17

Brand: Fagor Pages: 122

Brand: Waring Pages: 44

Brand: U-Line Pages: 57

Brand: ACM SRL & Escpresso Pages: 25

Brand: Sunbeam Pages: 2

Brand: PastaFacile Pages: 8

Brand: BOSKA Pages: 9

Brand: Capresso Pages: 2

Brand: HAEGER Pages: 44

Brand: Schaerer Pages: 2

Brand: Capresso Pages: 8

Brand: Focus Electrics Pages: 11

Brand: ELIS & Elsa Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands