Carilex Cari Chair Operation Manual Download Page 8

ANTI-DECUBITUS AIR ALTERNATING PRESSURE CUSHION REPLACEMENT SYSTEM

7

English

from Geri Chair Mode to Seating Cushion 
Mode.

Side Panel Features (Figure 5b on page 6)

Power Receptacle (1)
Insert power adaptor firmly into 
receptacle.

Couplers (2)
Quick release couplers are used to secure 
cushion air hoses to power unit.

Rear Panel Features 

Figure 5c on page 6

Hanger Install location (3)
The user can install Carilex optional 
hangers to hook the power unit on almost 
any foot board or IV pole.

Air Filter and Filter Cap (4)

Carilex recommends that the filter should 

be cleaned or replaced once a month to 
ensure optimal performance of the device.

Rocker Switch (5)
Main power switch of the power unit.

6.0 Cushion and 

Device 

Installations

[1] Remove existing article from geriatric 

chair, recliner, or wheelchair.

[2] Place Carilex cushion on the chair. 

Secure the cushion at each side by 

using anchor strap. Please verify all 

chair functions are working properly 

without interference before proceeding 

to the next step.

[3] Secure the power unit to the rear of the 

chair by using dedicated carry bag.

[4] Firmly connect the air hose couplings 

to the quick release couplers on the 

power unit’s air outlet.

[5] Push the rocker switch to "on" position 

at the rear side panel.

[6] Press       to turn on the power unit. 

Please switch to Geri Chair Mode 

or Seating Cushion Mode for your 

corresponding cushion.

CAUTION:

Please ensure to charge the power unit at 

least 8 hours before the first use.

7.0 Program Settings

[1] Assist the patient sitting on the center 

of cushion. Adjust the cushion’s 

internal pressure according to the 

patient sensation by Comfort Level 

Button. If the patient feels the 

cushion is too soft or firm, increases 

or decreases the cushion’s internal 

pressure one increment at a time 

and wait for the device to stabilize 

the internal pressure before making 

another change until a comfortable 

state is achieved.

[2] Caregivers should always perform a 

hand check by placing their hands 

underneath patient’s pelvis area to 

check if there is sufficient air support 

to ensure the patient is not bottoming 

out.

[3] IMPORTANT: TUCKING THE 

SHEET IN TIGHTLY REDUCES 

THE EFFECTIVENESS OF THE 

DEVICE.

Summary of Contents for Cari Chair















Reviews: