background image

Carefree of Colorado Service 

Manual 

E

CLIPSE

 

052547-301r10 

35 

S

TANDARD 

M

AINTENANCE

 

Maintaining a Carefree Awning is easy.  Just follow these basic steps: 

  Always operate the awning according to the instructions. 

  Periodically check that the fasteners are tight.  Tighten if necessary. 

  Keep the awning fabric and arms clean. 

F

ABRIC 

C

ARE

 

CAUTION  

Do not use oil based cleaners or any caustic, granulated, or abrasive type cleaners 

on your Carefree product. 

1.  One of the best ways to keep the fabric looking good and to delay the need for deep or vigorous 

cleanings is to hose fabrics off on a monthly basis with clear water.  This practice will help prevent dirt 
from becoming deeply imbedded in the fabric.  In most environments, a thorough cleaning will be 
needed every two to three years. 

2.  When it’s time for a thorough cleaning, the fabric can be cleaned while still on the awning frame. 

  For Vinyl Fabric – Use a soft brush and warm water with soap. 

  For Acrylic Fabric – Use a stiff brush and warm water with soap. 

3.  When cleaning the fabric, it is important to observe the following: 

  Always use a natural soap, never detergent. 

  Water should be cold to lukewarm, never more than 100

F. 

  Air-dry only.  Never apply heat to the fabric. 

  Always allow the fabric to dry thoroughly before rolling up the awning. 

Mildew 

Mildew is a fungus growth that looks like dirt.  Vinyl coated polyester fabrics are mildew resistant because 
of a chemical biocide in the vinyl coating.  Under ordinary conditions, mildew will not appear.  However, in 
areas where high temperature and humidity are common, mildew can be a problem and required the 
material to be washed more frequently.  Thoroughly rinse the fabric with clean water and allow to air dry 
completely before rolling up the awning. 

Pooling 

When water collects on the top of the fabric, this is known as "pooling".  This can occur during inclement 
weather or if a running air conditioner discharges over the awning.  The water is dumped when the awning 
is retracted.  It is recommended that if water accumulates on the top; retract the awning in steps (8"-12") to dump 
the water.  This will help prevent the fabric from stretching or distorting. 

The effects of wind and rain on an awning are unpredictable.  Severe damage to the awning and the 
vehicle may result.  I

F WIND OR EXTENDED PERIODS OF RAIN ARE EXPECTED

,

 ROLL UP THE AWNING AND 

SECURE FOR TRAVEL

A

RM 

C

ARE

 

The best method of keeping the arms and braces operating smoothly is to clean them.  Dirt and debris can 
cause the channels not to slide easily. 

Periodically wash out the channels with running water (i.e. a hose) to keep them clean.  If the channels still 
do not slide easily, lightly spray the joints and/or inside of the channels with a dry silicone lubricant, after 
the arms have been cleaned and dried thoroughly. 

Hardware Maintenance 

  Replace any parts that become damaged.  

  Periodically check all mounting hardware, screws, lags, etc., and re-tighten when necessary. 

M

OTOR 

M

AINTENANCE

 

  Check all wiring and connections for wear.  Repair when needed. 

Summary of Contents for ECLIPSE 2015














































Reviews: