background image

English

During Standby, press and hold the Volume Up Button for 

three seconds and you will hear a beep:

• One beep – Voice Connect set to Primary Buddy

• Two beeps – Voice Connect set to Secondary Buddy

MAKING AND RECEIVING MOBILE 

PHONE CALLS

PHONE FUNCTIONS

Answer a call

Tap the CTRL Button or speak loudly any word 

of your choice during an incoming call.

Reject a call

Tap the MC Button or remain silent for 15 

seconds during an incoming call.

Terminate a call

Tap the CTRL Button to end a call.

Voice Dial

During Standby, tap the CTRL Button and 

state the name of the person you wish to 

call. This feature is supported only by mobile 

phones that support the Voice Dial feature.

Redial

During Standby, press and hold the Volume 

Down Button for three seconds.

NOTES:

 If your 

Bluetooth

 mobile phone is paired to a 

Bluetooth

 GPS 

device, not directly to the 

scala rider Q2 

pro

, some of the above 

Phone functions may not be compatible.
When the headset is on an active phone call, any Buddy Intercom call 

request will be rejected automatically.
Once the phone call audio link drops, you can initiate and accept 

Buddy Intercom calls.

STATUS LIGHT STATES

None 

Headset is off

Alternating red and Blue 

flashes

Mobile phone Pairing mode

Simultaneous red and Blue 

flashes

GPS Pairing mode

Rapid Red flashes 

Intercom Pairing mode

1 blue flash every 3 seconds 

Standby – No call is in progress

2 blue flashes every 3 seconds 

Audio is on

1 red flash every 3 seconds 

Standby – Battery is low

2 red flashes every 3 seconds 

Low battery while audio is on

Solid red 

Headset is being charged

WORKING WITH THE FM RADIO

Your headset is equipped with an FM Radio receiver and RDS (Radio 

Data System) technology, allowing you to choose how and when you 
listen to your favorite stations.

The 

scala rider Q2 

pro

 enables you to listen to FM Radio while you 

are not receiving audio from another audio source. 
While listening to the radio, you do not have to worry about 
missing any calls, as the headset automatically mutes the FM 
Radio and switches to 

Bluetooth

 headset operation when an 

incoming call is received, or when you decide to initiate a call. 
When the conversation is over, the headset automatically tunes 
back in to the FM Radio.

The RDS Feature

Thanks to the RDS feature, your headset will automatically select the 

English

11

scala rider

® 

Q2

™ 

pro

Summary of Contents for SCALA RIDER Q2 PRO

















Reviews: