background image

8525-M316-O1 Rev A 

x

 8435(KG) 

5

BATTERY OPERATION, CONT. 

6.

If installing new batteries, proceed to 
step 7.  If replacing the batteries, remove 
all 6 batteries from the battery holder and 
then proceed to step 7. 

7.

Install the 6 new “AA” size batteries in 
the battery holder, noting the polarity 
markings located in the battery holder.
Refer to Figure No. 5. 

8.

After placing all 6 batteries in the holder, 
replace the battery cover. 

9.

Turn the indicator over (display facing 
up) and press the 

ON/OFF

key.

10.

If display turns on, batteries have been 
installed correctly. If not, remove panel 
and check for one or more improperly 
positioned batteries. 

11.

Return indicator to scale column bracket. 

12.

The scale is now ready for operation. 

Indicator Installation 

To install the indicator on the scale column bracket, place the screw heads on the back of the 
indicator into the large end of the slotted holes in the bracket.  Pull down to secure the 
indicator.  The spring plunger will lock the indicator to the bracket.  See Figures No. 6, 7 and 8. 

Figure No. 6 

Figure No. 8 

OPTIONAL AC POWER ADAPTER 

To power the scale using the optional 12 VDC wall plug-in AC power adapter, connect the plug 
from the adapter into the power jack on the back of the indicator and then plug the power 
adapter into the proper electrical outlet.  Refer to Figure 6.  On models requiring 230 VAC, it is 
the customer’s responsibility to obtain the correct power adapter plug. 

+           -

-           + 

-           + 

-           + 

+           -

+           -

Spring
Plunger

Scale
Cable

AC Power 
Adapter

Figure No. 7

Figure No. 5 

Spring
Plunger
Release

Scale
Cable

AC Power 
Adapter

Summary of Contents for Detecto 8435













Reviews: