background image

!

IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION

WARNING – INCORRECT INSTALLATION CAN LEAD TO SEVERE INJURY 
FOLLOW ALL INSTALLATION INSTRUCTIONS CAREFULLY

Before installing the operator check that the door is in good mechanical condition, 
and correctly balanced, and that it opens and closes properly.

Do not use the force adjustments to compensate for a binding or sticking garage door.
Excessive force will interfere with the proper operation of the Safety Reverse System 
or damage the garage door.

Do not wear rings, watches or loose clothing while installing or servicing a garage
door operator.

To avoid serious personal injury from entanglement, 

remove any ropes

connected to 

the garage door before installing the door operator.

Install the remote mounted bell push button within sight of the door but away from 
any moving parts and at a height of at least 1.5 metres.

The safety reverse system

test is very important. The garage door must reverse when

obstructed on closing. 

Failure to properly adjust the operator may

result in serious

personal injury from a closing garage door. Repeat the test once a month and make 
any needed adjustments (see Advanced Settings, Menu 

b

and Menu 

c

on page 15 of 

this manual).

Installation and wiring must be in compliance with your local building and electrical codes. 

If the garage has no service entrance door then an exterior release kit MUST be fitted. 
This accessory allows manual operation of the garage door from outside in case of 
power failure. 

Disconnect electric power to the garage door operator before making repairs or 
removing covers.

Use the manual release lever to disengage the motor drive ONLY when the drive is 
switched OFF and, if possible, when the door is fully closed.

Examine the installation, in particular the cables, spring and mountings, for signs of
wear, damage or imbalance. Do not use if repair or adjustment is needed since a fault 
in the installation or an incorrectly balanced door may cause injury.

IMPORTANT SAFETY NOTE
Only operate the door when the door is in full view, free of obstacles with no persons 
(particularly children) near the door. Nobody should be allowed to enter or leave the 
garage whilst the door is in motion.

Page 2

Summary of Contents for DC-650N





















Reviews: