5
12VDC POWER SUPPLY AND
AUTOMATIC MAINTENANCE
CHARGER FOR 12V LEAD-ACID
BATTERIES FROM 6Ah TO 96Ah.
DO NOT USE FOR NiCd, NiMH, Li-Ion OR NON-RECHARGEABLE BATTERIES.
IMPORTANT: READ THE FOLLOWING INSTRUCTIONS BEFORE USING.
This appliance can be used by children aged from 8 years and above and persons with
reduced physical,sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
SAFETY WARNING AND NOTES:
Batteries emit EXPLOSIVE GASES - prevent flame or sparks near batteries.
Disconnect
AC power supply before making or breaking DC/battery connections. Battery acid is highly corrosive. Wear protective clothing and eyewear and
avoid contact. In case of accidental contact, wash immediately with soap and water. Check that the battery posts are not loose; if so, have the
battery professionally assessed. If the battery posts are corroded, clean with a copper wire brush; if greasy or dirty clean with a rag damped in
detergent. Use the charger only if the input and output leads and connectors are in good, undamaged condition.
If the input cable is
damaged, it is essential to have it replaced without delay by the manufacturer, his authorised
service agent or a qualified workshop, to avoid danger.
Protect your charger from acid and acid fumes and from damp
and humid conditions both during use and in storage. Damage resulting from corrosion, oxidation or internal electrical short-circuiting is not
covered by warranty. Distance the charger from the battery during charging to avoid contamination by or exposure to acid or acidic vapours. If
using it in the horizontal orientation, place the charger on a hard, flat surface, but NOT on plastic, textile or leather. Use the fixing holes provided
in the enclosure base to attach the charger to any convenient, sound vertical surface.
EXPOSURE TO LIQUIDS:
This appliance is designed to withstand exposure to liquids accidentally spilled or splashed onto the
casing from above, or to light rainfall. Prolonged exposure to falling rain is inadvisable and longer service life will be obtained by minimizing
such exposure. Failure of the appliance due to oxidation resulting from the eventual penetration of liquid into the electronic components,
connectors or plugs, is not covered by warranty.
BATTERY CONNECTIONS:
2 interchangeable connection sets are available, supplied with the charger is a set of battery clips
for charging the battery off-vehicle, the other connection set comes with metal eyelet lugs for permanent connection to the battery posts,
and re-sealable weatherproof cap on the connector that connects to the charger output cable. This connection set allows easy and sure
connection of the charger to maintain the battery on-vehicle. The resealable weatherproof cap is designed to protect the connector from dirt
and damp whenever the charger is not attached. Consult a professional service agent for assistance in attaching the metal eyelets to the
battery posts. Secure the connector with weatherproof cap so that it cannot foul any moving part of the vehicle or the cable can be pinched
or damaged by sharp edges. The in-line fuse in the eyelets connection set protects the battery against such accidental shorting across
positive and negative conductors. Replace any burnt fuse only with a similar new fuse of 15A rating.
CONNECTING THE APPLIANCE: Follow this procedure carefully and exactly in this order,
1) Connect charger cable from the BATTERY CHARGER circuit securely to the vehicle’s 12V lead-acid battery.
OBSERVE THESE SAFETY PRECAUTIONS WHEN MAKING CONNECTIONS TO THE BATTERY
a. Disconnect AC power supply before making or breaking DC / battery connections.
b.
If charging a battery in the vehicle with the battery clips, before making connections, first check that the battery clips can be safely
and securely positioned clear from surrounding wiring, metal tubing or the chassis. Make connections in the following order:
First connect to the battery terminal not connected to the chassis (normally positive),
then connect the other battery clip (normally negative) to the chassis well away
from the battery and fuel line. Always disconnect in reverse sequence.
c.
When charging a battery out of the vehicle with the battery clips, place it in a well ventilated area. Connect the charger to the battery:
RED clamp to POSITIVE (POS, P or +) terminal and BLACK clamp to NEGATIVE (NEG, N or –) terminal. Make sure the connections are
firm and secure. Good contact is important.
d. If the battery is deeply discharged (and possibly sulphated), remove from the vehicle and inspect the battery before
connecting the charger for a recovery attempt.
Visually check the battery for mechanical defects such as a bulging or cracked
casing, or signs of electrolyte leakage. If the battery has filler caps and the plates within the cells can be seen from the outside, examine
the battery carefully to try to determine if any cells seem different to the others (for example, with white matter between the plates,
plates touching). If mechanical defects are apparent do not attempt to charge the battery, have the battery professionally assessed.
SAFETY
By CarCapsule
