Car-Interface CI-RL3-LR16-10 Manual Download

Page: 1 / 22

Version 03.07.2020

HW CAM(V98)/(V16)

CI-RL3-LR16-8/10

r.LiNK

Video inserter

CI-RL3-LR16-8

CI-RL3-LR16-10

Compatible with

Jaguar and Landrover vehicles

With Incontrol Touch system and 8inch monitor

or Incontrol Touch Pro system and 10.2inch Monitor

Video-inserter for one rear-view camera

and two additional video inputs

Product features



Video-inserter for factory-infotainment systems



CVBS Input for one rear-view camera



2 CVBS Video-inputs for after-market Video sources (e.g. DVD-Player, DVB-T Tuner)



Automatic switching to rear-view camera input on engagement of the reverse gear



Activatable parking guide lines for rear-view camera (not available for all vehicles)



Video-in-motion (ONLY for connected video-sources)



Video-inputs NTSC compatible

Summary of Contents for CI-RL3-LR16-10























Search results

Summary of Contents for CI-RL3-LR16-10

Reviews:

Related manuals for CI-RL3-LR16-10

Brands by name

Popular brands

Car-Interface CI-RL3-LR16-10, Manual

Search results

Summary of Contents for CI-RL3-LR16-10

Reviews:

Related manuals for CI-RL3-LR16-10

Brands by name

Popular brands