manualshive.com logo in svg

CaptiveWorks CW-3000HD, User Manual, Page: 35 / 107

Share
Download
CaptiveWorks CW-3000HD User Manual Download Page 35

Storage Setup

The CW-3000HD comes with an automated storage setup system that allows users to 

uncover enhanced features for improved usability and performance. 

     You've chosen to install an internal hard drive.

Here are some basic pointers and steps.

What you'll need: 

●

Hard drive device 

●

The appropriate interface cable

●

Phillips screwdriver 

●

Needle-nose pliers (IDE o

nly) 

NOTE: 

If you do not understand these instructions or lack good manual dexterity, have a qualified 
technician install the hard drive for you.

If at any time you are in doubt, look for more information. There are plenty of resources 

on the web as well as the CaptiveWorks forum.

1.

Turn off the CW-3000HD, unplug it, and take the top cover off.

2.

Make sure that you are properly grounded and if possible do the installation in an 
uncarpeted area.

3. Facing at the front of the CW-3000HD the hard drive bays are on the right hand side. 

Undo the top screw holding the hard drive carriage and swing it up and out.

4. Position hard drive in drive bay carriage and secure it with screws.
5. Connecting an IDE Hard drive:

a. Ensure that the jumper is set so that the hard drive will function on its own cable. 

This is usually Master though some hard drives vary. Refer to the hard drive 
manufacturer specifications.

b. Connect the data (ribbon) cable to back of hard drive. Align the colored band of the 

cable with pin No. 1 of the hard drive.

6. Connecting a SATA Hard drive:

a. Connect the SATA cable (skinny flat) to the back of the hard drive.

7. Connect the power cable from one of the connectors on power supply. Both SATA and 

4 pin molex connectors are available.

8. Slide the hard drive/carriage unit in at an angle and swing/rotate down into place.
9. Re-fasten the top screw that holds the hard drive/carriage assembly.
10. Double-check your connections and ensure the fan(s) are clear of any dangling wires.
11. Re-attach the top cover and screws.
12. Connect the power cord to CW-3000HD and power it on.

PAGE 35                                                                        

BACK

 

TO

 TOC

 

 

Summary of Contents for CW-3000HD












































































































Reviews:

No comments