Instruction manual DI652
29
Please keep this instruction manual for future reference
S TA RT I N G A C Y C L E WA S H
1. Draw out the lower and upper basket, load the dishes and push them back.
It is recommended to load the lower basket first, then the upper one.
2. Pour in the detergent.
3. Insert the plug into the socket. For the power supply, refer to the last page”Product fiche”.
Make sure that the water supply is turned on to full pressure.
4. Open the door, press the Power button.
5. Press the Program “ ” button or “ ” button to choose a program, the response light will
turn on. Then close the door, the dishwasher will start its cycle.
C H A N G I N G T H E P R O G R A M M I D - C Y C L E
A wash cycle can only be changed if it has been running for a short time otherwise, the detergent
may have already been released and the dishwasher may have already drained the wash water. If
this is the case, the dishwasher needs to be reset and the detergent dispenser must be refilled. To
reset the dishwasher, follow the instructions below:
1. Open the door a little to stop the dishwasher, after the spray arm stops working, you can open
the door completely.
2. Press and hold the Program “ ” button for more than three seconds and the machine will be
in stand by state.
3. You can change the program to the desired cycle setting.
Forget To Add A Dish?
A forgotten dish can be added any time before the detergent dispenser opens. If
this is the case, follow the instructions below:
1.
Open the door a little to stop the washing.
2.
After the spray arms stop working, you can open the door completely.
3.
Add the forgotten dishes.
4.
Close the door. The dishwasher will start after 10 seconds.
WARNING
It is dangerous to open the door
mid-cycle, as hot steam may
scald you.
16
1.
you can open the door completely.
2.
Press Program “ ” button more than three seconds the machine will be in stand
by state.
3.
You can change the program to the desired cycle setting.
Open the door a little to stop the dishwasher, after the spray arm stop working,
3 sec
Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which
would have a detrimental or adverse effect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area.
Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting salt consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed
based on the hardness of the water used. This is intended to optimise and customise
the level of salt consumption.
1.
Open the door and switch on the appliance
2.
P
Program
“ ”
3.
Program
“ ”
4.
Without operation in 5 seconds or press the Power button to complete the setup
and exit the setup mode.
;
ress the
button
for more than 5 seconds to start the water softener
set model within 60 seconds after the appliance was switched on;
Press the
button
to select the proper set according to your local
environment, the sets will change in the following sequence:
H3->H4->H5->H6->H1->H2->H3;
Please follow the steps below for adjustment in salt consumption.
dH=1.25 Clarke=1.78 fH=0.178mmol/l
°
°
°
1
The manufactory setting: H3
Contact your local water board for information on the hardness of your water supply.
0 - 5
6 - 11
12 - 17
18 - 22
23 - 34
35 - 55
German
dH
Salt consumption
(gram/cycle)
0 - 9
10 - 20
21 - 30
31 - 40
41 - 60
61 - 98
0 - 6
7 - 14
15 - 21
22 - 28
29 - 42
43 - 69
0 - 0.94
1.0 - 2.0
2.1 - 3.0
3.1 - 4.0
4.1 - 6.0
6.1 - 9.8
H1
H2
H3
H4
H5
H6
0
9
12
20
30
60
French
fH
Mmol/l
Water softener level
British
Clarke
WATER HARDNESS
7
Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which
would have a detrimental or adverse effect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area.
Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting salt consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed
based on the hardness of the water used. This is intended to optimise and customise
the level of salt consumption.
1.
Open the door and switch on the appliance
2.
P
Program
“ ”
3.
Program
“ ”
4.
Without operation in 5 seconds or press the Power button to complete the setup
and exit the setup mode.
;
ress the
button
for more than 5 seconds to start thewater softener
set model within 60 seconds after the appliance was switched on;
Press the
button
to select the proper set according to your local
environment, the sets will change in the following sequence:
H3->H4->H5->H6->H1->H2->H3;
Please follow the steps below for adjustment in salt consumption.
dH=1.25
Clarke=1.78
fH=0.178mmol/l
°
°
°
1
The manufactory setting: H3
Contact your local water board for information on the hardness of your water supply.
0 - 5
6 - 11
12 - 17
18 - 22
23 - 34
35 - 55
German
dH
Salt consumption
(gram/cycle)
0 - 9
10 - 20
21 - 30
31 - 40
41 - 60
61 - 98
0 - 6
7 - 14
15 - 21
22 - 28
29 - 42
43 - 69
0 - 0.94
1.0 - 2.0
2.1 - 3.0
3.1 - 4.0
4.1 - 6.0
6.1 - 9.8
H1
H2
H3
H4
H5
H6
0
9
12
20
30
60
French
fH
Mmol/l
Water softener level
British
Clarke
WATER HARDNESS
7
Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which
would have a detrimental or adverse effect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area.
Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting salt consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed
based on the hardness of the water used. This is intended to optimise and customise
the level of salt consumption.
1.
Open the door and switch on the appliance
2.
P
Program
“ ”
3.
Program
“ ”
4.
Without operation in 5 seconds or press the Power button to complete the setup
and exit the setup mode.
;
ress the
button
for more than 5 seconds to start the water softener
set model within 60 seconds after the appliance was switched on;
Press the
button
to select the proper set according to your local
environment, the sets will change in the following sequence:
H3->H4->H5->H6->H1->H2->H3;
Please follow the steps below for adjustment in salt consumption.
dH=1.25 Clarke=1.78 fH=0.178mmol/l
°
°
°
1
The manufactory setting: H3
Contact your local water board for information on the hardness of your water supply.
0 - 5
6 - 11
12 - 17
18 - 22
23 - 34
35 - 55
German
dH
Salt consumption
(gram/cycle)
0 - 9
10 - 20
21 - 30
31 - 40
41 - 60
61 - 98
0 - 6
7 - 14
15 - 21
22 - 28
29 - 42
43 - 69
0 - 0.94
1.0 - 2.0
2.1 - 3.0
3.1 - 4.0
4.1 - 6.0
6.1 - 9.8
H1
H2
H3
H4
H5
H6
0
9
12
20
30
60
French
fH
Mmol/l
Water softener level
British
Clarke
WATER HARDNESS
7