Instruction manual DI652
17
Please keep this instruction manual for future reference
A D J U S T I N G T H E R I N S E A I D R E S E RVO I R
To achieve a better drying performance with limited rinse aid, the dishwasher is designed to adjust
the consumption by user. Follow the below steps:
1. Open the door, power on the dishwasher by plugging in.
2. Within 60 seconds of step 1, press and hold the Program “ ” button for more than 5
seconds, and then press the Delay “ + ” button to enter the set model, the rinse aid indication
blinks as 1Hz frequency.
3. Press the Program “ ” button to select the proper set according to your using habits, the
sets will change in the following sequence: D1->D2->D3->D4->D5->D1. The higher the
number, the more rinse aid the dishwasher uses.
4. No operation in 5 seconds or pressing the Power button will exit the set model.
Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which
would have a detrimental or adverse effect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area.
Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting salt consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed
based on the hardness of the water used. This is intended to optimise and customise
the level of salt consumption.
1.
Open the door and switch on the appliance
2.
P
Program
“ ”
3.
Program
“ ”
4.
Without operation in 5 seconds or press the Power button to complete the setup
and exit the setup mode.
;
ress the
button
for more than 5 seconds to start the water softener
set model within 60 seconds after the appliance was switched on;
Press the
button
to select the proper set according to your local
environment, the sets will change in the following sequence:
H3->H4->H5->H6->H1->H2->H3;
Please follow the steps below for adjustment in salt consumption.
dH=1.25 Clarke=1.78 fH=0.178mmol/l
°
°
°
1
The manufactory setting: H3
Contact your local water board for information on the hardness of your water supply.
0 - 5
6 - 11
12 - 17
18 - 22
23 - 34
35 - 55
German
dH
Salt consumption
(gram/cycle)
0 - 9
10 - 20
21 - 30
31 - 40
41 - 60
61 - 98
0 - 6
7 - 14
15 - 21
22 - 28
29 - 42
43 - 69
0 - 0.94
1.0 - 2.0
2.1 - 3.0
3.1 - 4.0
4.1 - 6.0
6.1 - 9.8
H1
H2
H3
H4
H5
H6
0
9
12
20
30
60
French
fH
Mmol/l
Water softener level
British
Clarke
WATER HARDNESS
7
Water Softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the water, which
would have a detrimental or adverse effect on the operation of the appliance.
The more minerals there are, the harder your water is.
The softener should be adjusted according to the hardness of the water in your area.
Your local Water Authority can advise you on the hardness of the water in your area.
Adjusting salt consumption
The dishwasher is designed to allow for adjustment in the amount of salt consumed
based on the hardness of the water used. This is intended to optimise and customise
the level of salt consumption.
1.
Open the door and switch on the appliance
2.
P
Program
“ ”
3.
Program
“ ”
4.
Without operation in 5 seconds or press the Power button to complete the setup
and exit the setup mode.
;
ress the
button
for more than 5 seconds to start the water softener
set model within 60 seconds after the appliance was switched on;
Press the
button
to select the proper set according to your local
environment, the sets will change in the following sequence:
H3->H4->H5->H6->H1->H2->H3;
Please follow the steps below for adjustment in salt consumption.
dH=1.25 Clarke=1.78 fH=0.178mmol/l
°
°
°
1
The manufactory setting: H3
Contact your local water board for information on the hardness of your water supply.
0 - 5
6 - 11
12 - 17
18 - 22
23 - 34
35 - 55
German
dH
Salt consumption
(gram/cycle)
0 - 9
10 - 20
21 - 30
31 - 40
41 - 60
61 - 98
0 - 6
7 - 14
15 - 21
22 - 28
29 - 42
43 - 69
0 - 0.94
1.0 - 2.0
2.1 - 3.0
3.1 - 4.0
4.1 - 6.0
6.1 - 9.8
H1
H2
H3
H4
H5
H6
0
9
12
20
30
60
French
fH
Mmol/l
Water softener level
British
Clarke
WATER HARDNESS
7
12
Adjusting the rinse aid reservoir
To achieve a better drying performance with limited rinse aid, the dishwasher is
designed to adjust the consumption by user. Follow the below steps.
1.
Open the door, power on the dishwasher by plugging in;
2.
Within 60 seconds after step 1, press the Program “ ” button more than
5 seconds, and then press the Delay “ + ” button to enter the set model,
the rinse aid indication blinks as 1Hz frequency.
3.
Press the Program “ ” button to select the proper set according to your
using habits, the sets will change in the following sequence:
D1->D2->D3->D4->D5->D1. The higher the number, the more rinse aid the
dishwasher uses.
4.
Without operation in 5 seconds or press the Power button to exit the set model,
the set success.
Filling The Rinse Aid Reservoir
3
Close the cap once full.
1
2
Remove the rinse reservoir cap by
lifting up the handle .
Pour the rinse aid into the dispenser, being
careful not to overfill.
F I L L I N G T H E R I N S E A I D D I S P E N S E R
