CanyCom SC45 Operator'S Manual Download Page 55

Page: 55 / 64

-45-

Maintenance

1.  Remove filler cap. Fill fluid.
2.  Put filler cap back in place firmly.
3.  Run engine for a while to circulate hydraulic

fluid.

Filling

Hydraulics Belt

1. Remove belt cover.
2. Inspect drive belt tension. Push on the

middle of hydraulics belt with a finger to see
if its sag A is about 10mm. If not, adjust.

3. Visually inspect drive belt for damages. If

damaged, contact your dealer to replace it.

4. Install belt cover.

• Adjust belt tension properly. Inproperly tensioned belt may reduce performance

and its service life.

3571M-0508-040E

Inspecting

1.  Loosen four mount bolts.
2.  ILoosen lock nut.
3.  Adjust belt tension with adjust nut so that it

sags about 10mm when the middle of the
belt is pushed by a finger.

4. Tighten lock nut.
5. Tighten four mount bolts.

3574M-0507-040E

Lock Nut

Mount Bolts

Tension Bolt

Adjusting

3577M-0507-020US

Filler Cap

Summary of Contents for SC45

































































Search results

Summary of Contents for SC45

Reviews:

Related manuals for SC45

Brands by name

Popular brands

CanyCom SC45, Operator'S Manual

Search results

Summary of Contents for SC45

Reviews:

Related manuals for SC45

Brands by name

Popular brands