manualshive.com logo in svg

Canon K10158, User Manual

Share
Download
Canon K10158 User Manual Download Page 65

64

Chapter 6   Maintaining the Printer

Replacing the battery pack

Follow this procedure to replace the battery pack.

You can replace the battery pack at any time. You may want to
purchase and carry extra battery packs for emergencies. However,
please remember that new battery packs must be fully charged before
you can use them. Before you travel, make sure new battery packs are
fully charged. 

You must also replace a battery pack after it is exhausted. The

CHARGE/ERROR

lamp will flash and the printer will beep six times

when the battery pack becomes exhausted. After the battery pack is
exhausted, ti cannot be recharged and used again.

HANDLE THE BATTERY PACK CAREFULLY BY FOLLOWING THE

GUIDELINES DESCRIBED ON PAGE 21.

1.

Press the 

POWER

button to switch the printer off.

2.

If the optional sheet feeder is installed on the printer, remove it.

3.

If the front cover is closed, open it.

4.

Push the battery pack release to the right. The battery pack will
spring slightly out of the printer.

5.

Remove the battery pack from the printer.

Summary of Contents for K10158

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands