Canon JX510P User Manual Download | Manualshive

Page: 64 / 98

background image

62

Routine Maintenance

ENGLI

S

H

Routine Maintenance

Maintenance Menus

The table below shows the available maintenance menus when you press [Maintenance].

Replacing a FINE Cartridge

If there is no improvement with the quality of printing following such maintenance as FINE Cartridge
Cleaning, the FINE Cartridge is probably empty. Replace the empty FINE Cartridge with a new one.
When replacing a FINE Cartridge, check the model number very carefully.

Knowing When to Replace a FINE Cartridge

z

When Ink is Low

When the ink level is low, <RECOMEND NEW CRT> is displayed on the LCD and the Ink Lamp
lights up. In this state the FAX will receive documents to memory (up to 30 transactions or 120
pages (JX210P: 60 pages)) to prevent the information contained in the FAX from being lost if the
ink runs out completely. You need to print out received faxes manually from the <MEMORY
REFERENCE> menu.
After printing, delete unnecessary faxes from the memory. For more details, see “Documents
Stored in Memory” on page 40.

z

When Ink is Empty

When the ink is almost empty, <RECOMEND NEW CRT> is displayed on the LCD and the Ink
Lamp blinks. When this occurs it may not be possible to clearly print received faxes from
memory. When the ink is empty, <NO INK> is displayed on the LCD. Replace the FINE Cartridge
with new one. For more details, see “Replacing a FINE Cartridge” on page 64.
Printing will resume as soon as the FINE Cartridge is replaced.

z

Press [Stop/Reset] to cancel the current print job.

Replace the empty ink cartridge immediately after the printing. The resulting print quality is not
satisfactory, if printing is continued under the ink out condition.

Menus

<CS CLEANING> (see page 69)
<NOZZLE CHECK> (see page 65)
<CLEANING> (see page 66)
<DEEP CLEANING> (see page 66)
<ALIGN PRINT HEAD> (see page 67)
<HEAD ALIGN VALUE> (see page 67)
<ROLLER CLEANING> (see page 70)
<BOTTOM CLEANING> (see page 70)

Note

You can also perform the maintenance operation from your computer. For details, refer to the

On-screen

Manual

.

«
...
62
63
64
65
66
...
»

Summary of Contents for JX510P



































































































Reviews:

No comments

Related manuals for JX510P

Brand: OKIFAX Pages: 147

Brand: Janome Pages: 41

Carpetmaster 577

Brand: Clarke Pages: 21

Brand: Siruba Pages: 28

Brand: Pfaff Pages: 50

Brand: Alfa Network Pages: 157

Brand: JUKI Pages: 96

Aria Quilting & Sewing Machine

Brand: Baby Lock Pages: 2

Alto FLOORTEC 550 P

Brand: Nilfisk-Advance Pages: 60

Brand: Nilfisk-Advance Pages: 82

Brand: JUKI Pages: 120

Brand: JUKI Pages: 124

Brand: JUKI Pages: 108

Brand: Singer Pages: 54

Brand: JUKI Pages: 28

HZL - 353Z Series

Brand: JUKI Pages: 78

Brand: Stern Pinball Pages: 44

Brand: AMS Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands