manualshive.com logo in svg

Canon iPF720 - imagePROGRAF Color Inkjet Printer, Service Manual

Share
Download
Canon iPF720 - imagePROGRAF Color Inkjet Printer Service Manual Download Page 196

Chapter 8  

8-2

8.2 Warning Table

8.2.1 Warnings

0014-1952

* Codes represent the numbers that are displayed in DISPLAY in service mode and that are recorded in PRINTINF. Messages that are not accompanied by a code
indication are not logged.

T-8-2

Display massage

Code*

Condition detected

Action

Ink Level: Check

0180104-1000

BK ink tank near-empty

Renew the ink tanks.

Ink Level: Check

0180101-1001

Y ink tank near-empty

Ink Level: Check

0180102-1002

M ink tank near-empty

Ink Level: Check

0180103-1003

C ink tank near-empty

Ink Level: Check

0180106-1006

MBK ink tank near-empty

Ink Level: Check

0180106-1007

MBK2 ink tank near-empty

Problem with Printhead.
Chk printing results

01800500-1010

Number of non-discharging nozzles in 
printhead: Warning level

Clean the printheads. Renew the printheads. Identify the 
head management sensor unit.

Prepare for maint cart 
replacement.

01841001-281A

Maintenance cartridge near-full

Replace the maintenance cartridge.

Prepare for parts replacement.
Call for service.

Parts counter W1 level

Check the parts counter in service mode.

Parts replacement time has 
passed.
Call for service.

Parts counter W2 level

After checking the parts counter in service mode, 
replace any part whose counter is nearing the error 
value.

GARO W1221

01341221-1030

GARO (image mode): Unknown command Verify the transmitted data before reprinting.

GARO W1222

01341222-1031

GARO (image mode): Invalid parameter 
count (no parameters)

GARO W1223

01341223-1032

GARO (image mode): Required parameter 
missing

GARO W1225

01341225-1034

GARO (image mode): Other warning

GARO W1226

01341226-103A

GARO (image mode): Image processing 
table error

GARO W1231

01341231-1035

GARO (setup): Unknown command

GARO W1232

01341232-1036

GARO (setup): Invalid parameter count

GARO W1233

01341233-1037

GARO (setup): Required parameter 
missing

GARO W1234

01341234-1038

GARO (setup): Data out of bounds

GARO W1235

01341235-1039

GARO (setup): Other warning

End of paper feed.
Cannot feed paper more. 

Forced feed limit 

Check the remaining quantity of roll media.

This type of paper is not 
compatible with HP-GL/2.

01860006-1015

Non-support paper of HP-GL/2

Exchange for the compatible paper to HP-GL/2.

GL2:W0501
The memory is full.

01340501-1040

Memory full (HP-GL/2)

Check if there is the non-image area of the print.
Verify the transmitted data before reprinting.

GL2:W0904
The memory is full.

01340904-1048

Overflow of Polygon buffer (HP-GL/2)

GL2:W0903
The memory is full.

01340903-1047

Overflow of replot buffer (HP-GL/2)

GL2:W0502
The parameter is out of range.

01340502-1041

Invalid parameter (HP-GL/2)

Verify the transmitted data before reprinting.

GL2:W0504
This command is not supported.

01340504-1043

Invalid command (HP-GL/2)

Mail box nearly full.
Delete unwanted data

011A1001-2901

The free hard disk space left for Personal 
Boxes in the printer's hard disk does not 
have more than 1 GB, combined.

Delete unneeded jobs stored in Personal Boxes.

Mail box full.
Now printing without saving data.

01861003-2902

100 jobs are stored in the Personal Box.

Delete unneeded jobs stored in Personal Boxs.

Mail box full.
Delete unwanted data

011A1006-2906

Saved jobs exceed the Personal Box 
capacity.

Press the stop button to cancel the print job.
Delete print jobs from the queue.
Delete unneeded jobs stored on the hard disk.

Summary of Contents for iPF720 - imagePROGRAF Color Inkjet Printer













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands