manualshive.com logo in svg

Canon iPF720 - imagePROGRAF Color Inkjet Printer, Service Manual

Share
Download
Canon iPF720 - imagePROGRAF Color Inkjet Printer Service Manual Download Page 163

Chapter 6

6-17

6.3 Version Up

6.3.1 Firmware Update Tool

0013-6639

Use of the following tools allows you to update the firmware of the main controller incorporated in the printer.

- imagePROGRAF Firmware Update Tool
- L Printer Service Tool

1. imagePROGRAF Firmware Update Tool

imagePROGRAF Firmware Update Tool is the same as that for user.

Procedure:

1) Start imagePROGRAF Firmware Update Tool.
2) Place the printer in the online mode.
3) Transfer the firmware data to the printer according to the instructions shown on the display.
4) The data shown on the LCD on the operation panel changes and the firmware is updated automatically. 
5) When firmware update is completed, the printer will start again.

File transfer route:

USB, IEEE1394, network

2. L Printer Service Tool

Procedure:

1) Start L Printer Service Tool.
2) Place the printer in the online mode.
3) Specify the firmware file(jdl) and then transfer it.
4) The data shown on the LCD on the operation panel changes and the firmware is updated automatically. 
5) When firmware update is completed, the printer will start again.

File transfer route:

USB, IEEE1394, network

Summary of Contents for iPF720 - imagePROGRAF Color Inkjet Printer













































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands